Assume that 4-18mm diameter rivets join the plates that are each 120mm wide. The allowable stresses are 120MPa for bearing in the plate material and 60MPa for shearing of rivets. Determine the following: a. The minimum thickness of each plate b. The largest average tensile stress in the plate F=70

Q: The 130 mm wide plate shown has a working tensile stress of 75 MPa and the bearing stress between…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: The rectangular bar shown is connected to a support bracket with a 16 mm diameter pin. The width of…

A: Given: Diameter of pin = 16 mm Width of rectangular bar = 60 mm Bar thickness = 25 mm Maximum…

Q: 2. The bronze bar 3 m long with a cross-sectional area of 350 mm2 is placed between two rigid walls.…

A: Length of bar, L =3mCross sectional area of bar, A=350mm2Initial temparature, t1 =20°CCoefficient of…

Q: Question A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm…

A: Given : thickness of plate= 12mm  connect to 8mm thick plate  2×8>12  hence  t= 12mm Dia of rivet…

Q: toonges as aasm 12 mm thick plate is conected to two 8 mm thick plates, on either side through a 16…

A:

Q: A threaded steel rod (Es = 210 GPa, dr = 12 mm, as = 12 x 10-6/°C) is held stress free between rigid…

A: Given, Es=210 GPadr=12 mm4αs=12×10-6/°Cdp=15 mτ=45 MPaσ=70MPa

Q: DETERMINE THE AVERAGE PUNCHING SHEAR STRESS THE CIRCULAR SHAFT CREATES IN THE METAL PLATE THROUGH…

A:

Q: SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the…

A:

Q: Given: Four-25-mm-diameter rivets with an axial load of  T = 75 kN distributed equally as shown. The…

A:

Q: A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm diameter…

A:

Q: As demonstrated, four 25mm diameter rivets with a T=75kN axial load are equally distributed. The…

A: Shear stress in rivets: The plates are connected by rivets happens to exert tensile stress on the…

Q: In a steel flat plate a state of plane stress available. Calculate o, and principal stresse o, -140…

A:

Q: A plate is connected to another plate via 20 mm diameter rivets. It carries a load of P=155 kN at a…

A:

Q: Determine the largest weight “W” that can be supported by the two wires AB and AC. The working…

A:

Q: Two 10-mm thick plate members are to be connected using straps of the same thickness and 12-mm…

A:

Q: A plate with width of 300 millimeters and thickness of 20 milimeters is to be connected to two…

A:

Q: Two 10-mm thick plate members are to be connected using straps of the same thickness and 12-mm…

A: Given Data: Thickness of plates is t=10 mm. Diameter of rivet is d=12 mm. Maximum tensile stress on…

Q: 15 MPa 8 MPa to Determine the range of values of ox for which the maximum in-plane shearing stress…

A:

Q: : What torque can be applied without exceeding the shearing stress of 65 MPa in the bolts? Bolt…

A:

Q: Three round bars welded together are axially loaded as shown. Find the normal stress in each bar if…

A:

Q: A cast iron link is 50mm wide by 250mm high by 550 mm long. The allowable stress in tension is 50…

A:

Q: Q.1. A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138,…

A:

Q: Only considering stresses that are normal to the cross-sections you're designing. Where omax is the…

A:

Q: Two plate are joint by five rivets of 20 mm diameter. What is the shear stress in the material if…

A:

Q: The normal stress at point A equals to The shearing stress at point A equals to

A: Given:-Two posts connected as shown below   Required: To find a) Normal stress at point A and b)…

Q: SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the…

A: Force will be minimum of shear strength of bolts and axial strength of Plate

Q: PROBLEM 4: The figure shows a plate that is fastened to a fixed to a fixed member by five 12-mm-…

A:

Q: . For the riveted connection shown in the figure using  elastic analysis a. Determine the safe value…

A: Diameter of rivet = 25 mmAllowable shear stress = 150 MPaloading = 50 KNOther Data are given in the…

Q: ind the diameter of dAB BC вс + bar if the stress equal t .15GPA 120cm B 125kN 125kN 90cm A 60KN

A:

Q: A gusset plate is connected to the flange of column with the help of fillet weld on both sides as…

A:

Q: A Single rivet lop joint is to connect 12 mm thick plates by providing 20mm dia, rivet at so mm…

A: Given Data  Thickness of plate (t) = 12mm  Diameter of rivet (d) = 20mm  Pitch (P) = 50 mm  Working…

Q: SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the…

A:

Q: Consider the singly reinforced beam section given below (left figure). The stress block parameters…

A: Given- A singly reinforced beam section given as shown- M25 concrete, Fe415 steel, It is needed to…

Q: The plate has original dimensions 40 e strains Ex, Ey, and €₂?

A: We knowεx=σxE-μEσy+σz

Q: A steel latch is 6 mm thick. A force F of 3000 N is uniformly distributed as shov below. Do not…

A:

Q: The tensile member shown, 60mm x 80mm in cross-section is subjected to a load of 250kN. The plane…

A: Given data: P=250 kN cross-section Dimension=60 mm × 80 mm Angle =15o with X axis