The 130 mm wide plate shown has a working tensile stress of 75 MPa and the bearing stress between the plate and the rivet is limited to 100 MPa. The rivet used to connect the plates has a working shearing stress of 50 MPa. If the diameter of the rivet is 30 mm, determine the minimum safe thickness (mm) of each plate.

The 130 mm wide plate shown has a working tensile stress of 75 MPa and the bearing stress between the plate and the rivet is limited to 100 MPa. The rivet used to connect the plates has a working shearing stress of 50 MPa. If the diameter of the rivet is 30 mm, determine the minimum safe thickness (mm) of each plate.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

question 12 two decimal places
Two semi-spherical thin-walled vessels are joined together by attaching 40-mm bolts around the circumference to form a spherical vessel which can carry a pressure of 3 MPa. If the external diameter of the vessel is 2 m and the allowable stress in the bolts is 70 MPa, how many bolts must be used ? (answver in whole number) Use thickness 20 mm Nex
4.) A 150 x 90 x 12 angular section is welded to a gusset plate as shown in the figure. The angle is A36 steel with FY=248 MPa. The weld is E 80 electrode with Fu = 550 MPa. The allowable tensile stress for the angle is 0.6Fy and the allowable shear stress for the weld is 0.3Fu. The Area of the angular section is 2751 sq.mm. with y=51mm. CS 56 Which of the following most nearly gives the design force P? a.) 400,365.9 N b.) 409,348.8 N c.) 412,793.5 N d.) 420,366.6 N 5.) A W350 x 90 steel is used as a simply supported beam 8m long. The beam carries three equal concentrated loads at every quarter points. It also carries a uniform dead load o 5 kn/m (including its own weight) and a uniform live load of 7.20 kn/m. Properties of W 350 x 90 steel: bf = 250 mm The allowable bending stress is 0.66Fy. The allowable shear stress is 0.40Fy. The allowable deflection is L/360. Use Fx=248 Mpa and E=200 Gpa. tf = 16.40 mm V d = 350 mm Determine the maximum value of each concentrated load based on…
A 6-inch diameter pulley mounted on a 2-inch shaft as shown below transmits 9 kW at 1000 rpm. What is the combined stress acting on the shaft? Pulley 1020 Steel Shaft Scm 25cm
Calculate the value of P so that the allowable tensile stress on net area will not be exceeded. USE NSCP 2015.
What is the axial stress in the bronze rod (in MPa)? 2m 3m 6o kN mm 15mm banzerod
A scuba tank is being designed for an internal pressure of 2,655 psi with a factor of safety of 2.0 with respect to yielding. The yield stress of the steel is 67,000 psi in tension and 25,000 psi in shear. (Assume that the given radius or diameter is an inside dimension and that all internal pressures are gage pressures.) (a) If the diameter of the tank is 7.0 in., what is the minimum required wall thickness (in inches)? 0.277 X inches (b) If the wall thickness is 0.25 in., what is the maximum acceptable internal pressure (in psi)? 2392.85 psi
The steel shafts are connected together using a fillet weld as shown in the figure below. (Figure 1) Figure ▾ art A Tavg for Part A for Part 12 mm Value T= 60 N-m 50 mm- Determine the average shear stress in the weld along section a-a if the torque applied to the shafts is T = 63 N-m. Note: The critical section where the weld fails is along section a-s. Express your answer to three significant figures and include the appropriate units. Units 12 mm 1 12 mm 12 mm a do for Part 1 of 1 redo for Part A reset for Part A keyboard shortcuts for Part A help for Part A
SITUATION 14: A PL 300 x 20 mm is to be connected to two plates of the same material with half the thickness by 25 mm Ø rivets as shown in the figure. The rivet holes have a diameter 2 mm larger than the rivet diameter. The plate is A36 steel with Fy= 250 MPa, allowable tensile stress of 0.60Fy and allowable bearing stress of 1.35Fy. The rivets are A502, Grade 2, hotdriven rivets with allowable shear stress of 150 MPa. 25 mm Ø rivets + + PL 300x20 P/2 P P/2 PL 300x10 43. Which of the following most nearly gives the max. load in kN that can be applied to the connection without exceeding the allowable shear stress in the rivets? a. 675 KN b. 490 KN c. 598 KN d. 790.5 kN 44. Which of the following most nearly gives the max. load in kN that can be applied to the connection without exceeding the allowable bearing stress between the plates and the rivets? a. 490 KN b. 675 KN c. 598 KN d. 790.5 kN 45. Which of the following most nearly gives the max. load in kN that can be applied to the…
Please provide complete and step by step solution
Solve please, thank you
FREE BODY DIAGRAM PLEASE ASA