1. The assembly consists of three disks A, B and C that are used to support the load of 140 kN. If d₁= 25 mm, d₂ = 70 mm and d3 = 30 mm, determine the following. a) The compressive stress in disk A b) The shear stress in disk B c) The bearing stress in disk C C B A 140 kN 1-d3 - ・d₂ 20 mm 10 mm

1. The assembly consists of three disks A, B and C that are used to support the load of 140 kN. If d₁= 25 mm, d₂ = 70 mm and d3 = 30 mm, determine the following. a) The compressive stress in disk A b) The shear stress in disk B c) The bearing stress in disk C C B A 140 kN 1-d3 - ・d₂ 20 mm 10 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An embedded beam is subjected to the loads shown. Determine the stress produced at points A, B ,C, D in the embedment section. The X axis is 72.9 mm from the top edge. Solve correctly please
1. Determine the following: a. Determine the moment of inertia of the section about its neutral axis. b. Maximum tensile stress in the beam c. Maximum compressive stress in the beam 300 N/m 625 mm T: 100 mm 500 mm A B 3 m 1.5 m 100 mm
A channel-section has the dimensions as shown. Consider a cantilevered beam subjected to an end force P. L = 100 cm a) iif cross-section las is used, determine its normal stress distribution. (a) (b) b) if you stack two las sections as a box, but leave a gap between them, two sections carry = loadings with the same distribution pattern. Try express the results. (C) 2ª L 2CM дом E 2ch weld
The question is in the picture. Thanks
(4) Two kids (200 N each) are balanced on a seesaw. Plane a-a (containing Point A) is just left of the pin support. Plane b-b (containing Point B) is just right of the pin support. Illustrate the combined state of stress at Point A and at Point B on the two stress cubes below. (Yes, compute values, of course.) Ans. 214 kPa 1.2m 1.2m Point A (on plane a-a): x y ^y 4 200 N A SEESAW GIVEN: Iy= 2.488 E6 mm 4 I₂0.9338 E6 mm 4 12 14 14 12 N 12 ib 33 лу 33 x 2000 Points A&B dims. in mm Point B (on plane b-b): ^y ------ NA x ----- N
A 75 mm x 75 mm wooden block in cross section is subjected to a load P of 300 kN. The plane A makes an angle of 14 degrees with respect to the horizontal axis (x-axis). a. Determine the normal stress at section A-A. b. Determine the shear stress at section A-A.
1. A steel circular bar (the yield stress oy = 350 MPa) with diameter d = 60mm is acted upon by combined moments M and axial compressive loads P at its ends. Taking P = 500 kN, determine, based on the Von Mises criterion of yield failure, the largest allowable value of M. d M M P- P.
3. A 75 mm x 75 mm wooden block in cross section is subjected to a load P of 300 kN. The plane A makes an angle of 14 degrees with respect to the horizontal axis (x-axis). a. Determine the normal stress at section A-A. b. Determine the shear stress at section A-A. 300 kN A V 300 kN
Calculate the safe shear stress value of the shaft, given that the smallest allowable diameter d of the shaft subjected to forces P and Q is given as 60 mm in the figure?
Determine normal stresses at A and B. Are these point of maximum and minimum normal stresses? If not where are they located and what their values.
please answer, with written solution thanks
Consider a fillet section subjected to a tensile force F. Knowing that the fillet section has a uniform thickness of 5 mm and a yielding stress of 250 MPa, determine the force F that initiated the yielding of the fillet section. a.1.25 kN b.2.5 kN c.4 kN F d.2 kN 40 mm 25 mm 40 mm ↓ Which of the following is FALSE regarding the equation for deformation, 8=PL/AE? A. The term AE refers to the resistance of the member against axial deformation B.It can be used even for non-prismatic members C.It can only be used to compute for the elastic axial deformation of the member D. The term P refers to the internal axial force at the section considered A rigid bar ABC is loaded and supported as shown in the figure. After the load P is applied, the deformation of bar BD, SBD 0.6mm. What is the displacement at point B? A.0.36 mm B.0.48 mm P C.0.75 mm D.1.00 mm C 0.3 m 0.3 m Which of the following statements is TRUE for a circular shaft under pure torsion? A. The angle of twist of a point on the…