Give me the solution of these with these answers:2. ?? = 107.725 MPa3. the shear stress in the anchorbolts. Ans: ? = 91.44 Mpa 3. theshearstressintheanchorbolts.40°Pin(a)(b) A steel strut S serving as a brace for aboat hoist transmits a compressive forceP =54kN to the deck of a pier. Thestrut hasa hollow square crosssectionwith a wall thickness t12mm and theanglehorizontal is 40°. A pin through the struttransmits the compressive force from thestrut to two gussets G that are welded toebetweenthestrutandthethe base plate B. Four anchor bolts fastenthe base plate to the deck. The diameterof the pin is dthe gussets isof the base plate is Bt =8diameter of the anchor bolts is bolt d =18 mm, the thickness of15 mm, the thicknesstGmm, and the12mm. Determine the following stresses:2.the bearingstressbetweentheanchor boltsandthe base plate,

Answered: Image /qna-images/answer/ff9b490c-507b-48ad-b665-5ac5403dbdc5.jpg

Answered: Give me the solution of these with…

Give me the solution of these with these answers: 2. ?? = 107.725 MPa 3. the shear stress in the anchor bolts. Ans: ? = 91.44 Mpa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

How many zero force members are there in the truss shown? F. [E Hl100 '1 60 VKN kN 60 ♥kN Select one: O a. 4 O b. 2 О с. 1 O d. 3
I need solution in 15 minuties pleas
Calculate the maximum tensile and compressive stresses in the section of BC of the beam. BLO Nara 0.5 in LOO KN 1.5 m ( 1.00 KN C 0.5 m D 200 inn 100 mm 25 mm 150 mm t T 25 mm
Badly needed. please. with FBD
c) The three suspender bars are made of A-36 steel and have equal cross-sectional areas of 450 mm² .Determine the average normal stress in each bar if the rigid beam is subjected to the loading shown. A B C 80 kN 2 m 50 kN D E F -1m--1m--1 m--1m-|
2 - For beam I with distributed and concentrated loads, determine: a)The maximum shear stresses of interest along the beam height (draw the stress diagram); B)How far should the screws be placed along the beam so that resist shear. *Consider that each screws resists 6kN to shear.
The horizontal platform ABCD has a 300 lb weight actingvertically through its center. The platform is held in equilibriumby hinges at A and B and by brace CE (brace DE has beenremoved). The hinge at A acts as a journal bearing and does notexert an axial force. Determine the reactions at the hinges andthe force exerted by the remaining brace CE Please provide an FBD and show all written work, thank you!
( A ) Fixed ( C ) hinge ( D ) Fixed Please solve moment distribution Please solve moment distribution
Draw the SFD and BMD for the following frame. 120 KN 30 kN/m 60 KN 8 m A >>> 3 m 1 m B 6 m
Where is/are the location(s) of the maximum transverese shear stress? A simple I-beam is loaded as shown. 20 mm P KN PKN PKN Į Į -C B с D L/4 m L/4 m Midspan at point C Roller at E at the NA Section B at the top fiber Pin A at point C Midspan at point D Roller E at point D L/4 m L/4 m OE 20 mm 20 mm- 250 mm 150 mm 150 mm A
Needanswer ASAP ty!
Q1) In the pin-jointed frame shown in Figure Q1: a) calculate the unknown loads Fcx, Fox and Foy b) calculate the forces in links AB and AE indicating if it is a tie or strut, c) Indicate one failure mode each for a tie and strut member. 1.75 m FDY Fcx FDX -1.75 m B 00 E 10 KN 1.25 m A 5 KN