Two vertical forces, each of magnitude P= 8 kN, are applied to a beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam. 10 mm 10 mm 50 mm 50 mm 10 mm The maximum tensile stress is The maximum compressive stress is B 150 mm MPa. -250 mm MPa. C 150 mm D

Two vertical forces, each of magnitude P= 8 kN, are applied to a beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam. 10 mm 10 mm 50 mm 50 mm 10 mm The maximum tensile stress is The maximum compressive stress is B 150 mm MPa. -250 mm MPa. C 150 mm D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two identical plates are connected by two 18-mm diameter rivets as shown. Consider the following dimensions: B = 200 mm t = 22 mm x = 16 mm The allowable stresses of the plate are the following: Normal stress = 18 MPa Bearing stress = 4 MPa Shearing stress = 5 MPa Determine the maximum force P: A. Considering the normal stress: P = B. Considering the bearing stress: P = C. Considering the shearing stress: P = Express your answers in three decimal places. KN kN KN O CHEGG.CO ISL STRI NG URVE VARSITY TUTUP INST UTORIAL TE SUCH, B O CHEGG COURSEHERO, SKOOLI TUTORET TUTURME VARSITY TUTORS, WZANT. ETC. DISTRIBUTION TO ANY PARTY IS PROHIBITED, INSTITUTIONAL EXAM NOT EUPLOADING ON ANY TUTORIAL SITE SUCH LEDO CHEGG, COURSEHERO, SKOTTOREYZ TUTORM VARSITY TUTORS, W ZAWI, ETC. P4 DISTRIBUTION TO ANY PARTY IS PROHIBITED. NOT P SN INSTITUTIONAL EXEM NOT FOR REUPLNG ON ANY TUTORIAL SITE SUC 30 CHEGG, COURSEHERO, SKOOL TUTO+STORM VARSITY TUTORS, W DISTRIBUTION TO ANY RTY IS PROHIBITED. THERO, SKOOL…
In the shown diagram below, the curved out bar has an axis that is circular (with mean radius r = 12in) and is subjected to the m horizontal forces P = 400lb at the two ends. The cross-section of the bar is a triangular shape with height h and thickness t. If the allowable tensile stress in the bar is 12,000 psi, and height h=1.2 in, what's the minimum thickness tmin that is required?
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa
4. A rigid block of having a weight M is suspended by symmetrically placed rods. Each copper rod has an area of 1200 sq.mm: E= 125,000 MPa and the allowable stress is 90 MPa. The steel rod has an area of 1500 sq.mm; E 220GPa; and the allowable stress is 120 Mpa. Determine the largest weight M which can be supported by the rods. 8c=8s Copper 160 mm Pc Ps Steel 240 mm TIT Pc ..initial level Tinal level Copper 160 mm
d = 600 6Ø28 75 75 300 can you please show how to find the elastic stress and design ratio? fc' = 27 MPa; M1 = 60 KN-m; M2 = 200 KN-m
When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and C is 0.18 in. In segment (2), the normal strain is measured as 1,650 pin/in. Assume L₁ - 34 in. and L₂-83 in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar. (1) Answers: (a) in.& (b) = 4 i B (2) 4₂ in, pin/in.
THE BEAMS SHOWN IN FIGURES (a) AND (b) HAS THE FOLLOWING PROPERTIES. f’c =30 MPa, fy=400 MPa AND IS SUBJECTED TO A POSITIVE BENDING MOMENT Mu=140KN-m. ANSWER THE FOLLOWING.1. DRAW THE INTERNAL STRESS AND STRAIN DIAGRAM OF BEAM CONSIDERING THAT THE DEPTH OF THE STRESS BLOCK IS GREATER THAN THE THICKNESS OF THE FLANGE.
SIR, PLS GIVE ME PROPER AND CORRECT SOLUTION WITH DETAIL. THANKS