2. Two angle bars B and C are riveted to bracket A. Knowing that both angle bars are in compression and that force is 25 kN in angle bar B and 40 kN in angle bar C, determine the following: a. Number of 19 mm diameter rivets in angle bar B if the allowable bearing stress of angle bar is 60 MPa. Thickness of angle bar B is 6 mm. b. Number of 19 mm diameter rivets in angle bar C if the allowable shearing stress of rivets is 25 MPa. Thickness of angle bar is 5 mm. A 45⁰. B-0-0-0-0- 20° 0-0-

2. Two angle bars B and C are riveted to bracket A. Knowing that both angle bars are in compression and that force is 25 kN in angle bar B and 40 kN in angle bar C, determine the following: a. Number of 19 mm diameter rivets in angle bar B if the allowable bearing stress of angle bar is 60 MPa. Thickness of angle bar B is 6 mm. b. Number of 19 mm diameter rivets in angle bar C if the allowable shearing stress of rivets is 25 MPa. Thickness of angle bar is 5 mm. A 45⁰. B-0-0-0-0- 20° 0-0-

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Related questions

Q: An overhead paint conveyor will run for 7 hours continuously per day. There are no allowances and…

Q: Hello could you include the converting process in the step 3? It's quite confusing

Q: m trying to learn, this is not a clear explantion

Q: Describe about Oxidation Procedures.

A: Oxidation procedure:

Q: Name the two primary types of float?

Q: Question 3: Calculate the vertical stress induced at point A located 5 m deep under the embankment…

A: Data given Find : the vertical stress at point A

Q: Make a simple sketch of the septic tank and the advanced processing system (can be handwritten or…

A: As per company's guidelines we can only answer first question Kindly post other questions as…

Q: What is meant by “hydration”?

A: Hydration general definition in context of our body is the capacity of the body to absorb water or…

Q: Compute the cumulative percent retained on, and percent passing each sieve.

A: Sieve No. Weight Retained Cumulative Weight Retained % Cumulative…

Q: What is asphalt concrete paving material? A mixture of concrete and asphalt Bitumen and aggregate…

A: Given:What is asphalt concrete paving material?A mixture of concrete and asphaltBitumen and…

Q: mention Color Inspection Applications In Environmental Engineering

A: Environmental Engineering: - It is a branch of engineering in which study about the process and…

Q: What is the vadose zone, capillary fringe zone, and phreatic zone

A: Groundwater:- Water that is underground and can be found in voids and cracks in sand, rock, and…

Q: Refer to the attached plan and section to answer the succeeding questions 12mm THK. SLAB COVER WITH…

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: Define Subgrade Reaction Method.

A: Subgrade reaction method:

Q: Describe the Piston Sampler.

A: The piston sampler is described in the following step-

Q: Define the term Vibratory compactors.

A: A vibratory compactor can be defined as it is a heavy-duty machine, which uses both a roller or…

Concept explainers

Planar Stresses

Question

Full solution only.

2. Two angle bars B and C are riveted to bracket A. Knowing that both angle bars are in
compression and that force is 25 kN in angle bar B and 40 kN in angle bar C, determine the
following:
a. Number of 19 mm diameter rivets in angle bar B if the allowable bearing stress of angle bar
is 60 MPa. Thickness of angle bar B is 6 mm.
Number of 19 mm diameter rivets in angle bar C if the allowable shearing stress of rivets is
25 MPa. Thickness of angle bar is 5 mm.
b.
20°.
450
-O-O-0-0-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft. Figure P6.4
A 2.0 m wide strip foundation is placed in sand at 1.0 m depth. The properties of the sand are: = 19.5 kN/m3, c = 0 and =34. Determine the maximum wall load that the foundation can carry, with a factor of safety of 3.0, using a. Terzaghis original bearing capacity equation with his bearing capacity factors b. Meyerhofs modified bearing capacity equation with appropriate factors (Tables 16.2 and 16.3).
A beam is part of the framing system for the floor of an office building. The floor is subjected to both dead loads and live loads. The maximum moment caused by the service dead load is 45 ft-kips, and the maximum moment for the service live load is 63 ft-kips (these moments occur at the same location on the beam and can therefore be combined). a. If load and resistance factor design is used, determine the maximum factored bending moment (required moment strength). What is the controlling AISC load combination? b. What is the required nominal moment strength for a resistance factor of 0.90? c. If allowable strength design is used, determine the required moment strength. What is the controlling AISC lead combination? d. What is the required nominal moment strength for a safety factor of 1.67?
EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on the two planes are Plane EB: EB = 25 kN/m2; EB = +10 kN/m2 Plane FG: FG = 10 kN/m2; FG = 5 kN/m2 (Note: Mohrs circle sign conventions for stresses are used above) Given ; = 25, determine: a. The maximum and minimum principal stresses b. The angle between the planes EB and FG c. The external stresses on planes AB and BC that would cause the above internal stresses on planes EB and FG
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
Determine the smallest value of yield stress Fy, for which a W-, M-, or S-shape from Part 1 of the Manual will become slender. To which shapes does this value apply? What conclusion can you draw from your answer?
A square foundation is shown in Figure P6.19. Use FS = 6, and determine the size of the foundation. Use Prakash and Saran’s method [Eq. (6.59)]. Figure P6.19
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
A continuous foundation is required in a soil where c=10kN/m2, =26, and =19.0kN/m3. The depth of the footing will be 1.0 m. The dead load and the live load are 600 kN/m and 400 kN/m, respectively. Determine the required width for the foundation based on allowable stress design with FS = 3, using Eq. (6.10) and Table 6.1.
Determine the factor of safety against bottom heave for the braced cut described in Problem 15.18. Use Eqs. (15.66) and (15.70). For Eq. (15.70), assume the length of the cut, L = 18 m. 15.18 Refer to Figure 15.51 in which = 17.5 kN/m3, c = 60 kN/m2, and center-to-center spacing of struts is 5 m. Draw the earth pressure envelope and determine the strut loads at levels A, B, and C. FIG. 15.51