Situation 21 The compound shaft as shown is attached to rigid supports. It is subjected to a concentrated torque at the junction. The length of the steel segment is Im. 3. Determine the ratio of the length of the steel segment to that of the bronze such that the materials will be stressed to their limits. 4. Determine the tarsianal reaction, in N-m, at the right supports if the applied torque at the junction is maximized. 5. Determine the angle of twist, in " degrees, at the junction. Bronze 75 mm G 35 GPa 0 MPa Steel 50 mm T 0 MPa

Situation 21 The compound shaft as shown is attached to rigid supports. It is subjected to a concentrated torque at the junction. The length of the steel segment is Im. 3. Determine the ratio of the length of the steel segment to that of the bronze such that the materials will be stressed to their limits. 4. Determine the tarsianal reaction, in N-m, at the right supports if the applied torque at the junction is maximized. 5. Determine the angle of twist, in " degrees, at the junction. Bronze 75 mm G 35 GPa 0 MPa Steel 50 mm T 0 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Steel A-450 mm² E-200 GPa L-4.0 m A B opper A=230 mm² E-120 GPa L= 3.0 m 5.0 m a) What maximum P can be applied on the horizontal bar to give a stress of 110 MPa to steel and 150 MPa to copper. How far from copper should P be acting. Neglect the weight of the bar. b) What are the amount of deformations of the rods
Situation 2| The compound shaft as shown is attached to rigid supports. It is subjected to a concentrated torque at the junction. The length of the steel segment is 1m. 3. Determine the ratio of the length of the steel segment to that of the bronze such that the materials will be stressed to their limits. 4. Determine the torsional reaction, in N-m, at the right supports if the applied torque at the junction is maximized. 5. Determine the angle of twist, in ° degrees, at the junction. Bronze = 75 mm G = 35 GPa T= 60 MPa Steel = 50 mm G = 83 GPa = 80 MPa %D Tll IA a b.
A shaft composed of segments AC, CD and DB is fastened to rigid supports and loaded as shown. For steel, G = 83 GPa; for aluminum, G = 28 GPa; and for bronze, G = 35 GPa. Determine the reaction at B, the stress in the aluminum and the maximum stress in the bronze. Tc = 300 N-m Tp = 700 N-m 4. D Bronze 25 mm Steel C Aluminum 25 mm o 50 mm 2 m - 1.5 m 1 m
C 1.5 m B 950 Nm 0.7 m 50 mm A The rod shown above is composed of two connected segments: AB is steel with shear modulus Gsteel = 75 GPa and BC is brass with shear modulus Grass = 40 GPa. The steel segment has a diameter of 50 mm. a) Determine the required diameter of the brass segment such that the reaction at A will equal the reaction at C under the applied torque of 950 Nm at B. b) What is the magnitude and direction of the reactions at A and C? c) What is the maximum shear stress developed in the steel and brass rods d) What is the angle of twist at B relative to C?
make it simple just solution and answer
Problem 3: Inside a steel tube, 2.4 meters long, 34 mm radius, and 1.5 mm thick, 32.5A circular bar made of aluminum with a radius of mm is inserted and these two materials arethey are linked together to form a cross section that will work. This cantilever beam obtained from end Ait is fixedly supported. This cantilever beam,A torque of T = 900 Nm from end B(torque) is applied. Stiffness modulus of steel, Strength= 77 GPa and the stiffness modulus of aluminum Gal = 26Since GPa is the rotation at point BWhat is the (torsion) angle? Calculate.
Problem 3 The aluminum rod BC (G = 26 GPa) is bonded to the brass rod AB (G = 39 GPa). Knowing that each rod is solid and has a diameter of 12 mm, determine the angle of twist (a) at B, (b) at C. 200 mm Brass - Aluminum 300 mm C 100 N. m
Solution plz
Statically Indeterminate Problems
H1
Hand written and clean writing please
Solid mech.