The pin is used to connect the three links together. Due to wear, the load is distributed over the top and bottom of the pin as shown on the free-body diagram. The diameter of the pin is d = 11.4 mm. (Figure 1) Part A Determine the maximum bending stress on the cross-sectional area at the center section a-a. For the solution it is first necessary to determine the load intensities w and w2. Express your answer to three significant figures and include the appropriate units. Omax = Value Units Submit Request Answer Figure 1 of 1 > < Return to Assignment Provide Feedback 3600 N 25 mm 25 mm 40 mm 1800 N 1800 N

The pin is used to connect the three links together. Due to wear, the load is distributed over the top and bottom of the pin as shown on the free-body diagram. The diameter of the pin is d = 11.4 mm. (Figure 1) Part A Determine the maximum bending stress on the cross-sectional area at the center section a-a. For the solution it is first necessary to determine the load intensities w and w2. Express your answer to three significant figures and include the appropriate units. Omax = Value Units Submit Request Answer Figure 1 of 1 > < Return to Assignment Provide Feedback 3600 N 25 mm 25 mm 40 mm 1800 N 1800 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Stresses at any point in a simple axial member do not depend on the orientation of the plane being considered.
The steel used for the step shaft has an allowable shear stress of Tallow = 8 MPa. If the radius at the transition between the cross sections is r = 2.25 mm, determine the maximum torque T that can be applied. 30 mm FIN 15 mm T 30 mm T 2
The rigid bar of ABCD of negligible weight is supported hinge at A, steel rod at B and bronze rod at D. The properties of the rods are given in the Table. The assembly is initially stress-free. If the temperature rises by 20 degrees Celsius after a load W = 140 kN is applied, determine (a) the stress in the steel rod and the bronze rod and (b) the deformation of the steel rod and bronze rod
CN=44
An element in the beam is subjected tog following principal stresses, o, = 40 MPa, o, = -30 MPa, the diameter of the Mohr's circle is
Determine the stresses in each bar and the bond reactions.
Could you please provide a conceptual explanation with this?
Rigid bar ABCD is loaded and supported as shown. Steel [E = 28400 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.82 in.² and bar (2) has a cross-sectional area of 0.41 in.². After load P is applied, the strain in bar (1) is found to be 700 μe. Assume L₁=69 in., L₂-89 in., a=34 in., b=33 in., and c-37 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection VD of point D on the rigid bar. (c) the load P. A Answers: (a) 0₁ = (b) VD = (c) P= i i i L₁ a (1) B L2 b ksi, 0₂ = in. kips. (2) C i D P ksi.
I'd think that the bending stress of B is the result given in D and viceversa. Why is that not the case?
The brass wire has a triangular cross section, 2mm on a side. The yield stress for brass is Ty= 208 MPa. Gbr= 37 GPa. Determine the maximum torque to which it can be subjected so that the wire will not yield and the angle of twist
2. Determine the normal stress in members BD, AC, and BC in the truss shown. The cross- sectional area of each member is 1500 mm2. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value. 10 m 10 m 10 m K 6 т H 6 т 15° 15° 50 kN 40 kN E F 6 т C D б т A B
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1350 µm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. A 240 mm B (1) O 1281 um/m O 1877 µm/m O 1141 µm/m O 1358 µm/m O 999 µm/m 360 mm (2) Rigid bar 900 mm C 140 mm, 1,500 mm