Compound axial mermber ABC has a uniform diarneter of d= 1.25 in. • Segment (1) is an aluminum (E, - 10000 ksi) alloy. The length of segment (1) is L1 - 100 in. • Segment (2) is a copper (E2 = 17000 ksi] alloy. The length of segment (2) is L2 - 140 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of €2 = 2300 uin/in. in the longitudinal direction. What is the total elongation of member ABC? L2 Aluminum B (2) Соpрer Answer: AL - i in.

Compound axial mermber ABC has a uniform diarneter of d= 1.25 in. • Segment (1) is an aluminum (E, - 10000 ksi) alloy. The length of segment (1) is L1 - 100 in. • Segment (2) is a copper (E2 = 17000 ksi] alloy. The length of segment (2) is L2 - 140 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of €2 = 2300 uin/in. in the longitudinal direction. What is the total elongation of member ABC? L2 Aluminum B (2) Соpрer Answer: AL - i in.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.15P: Estimate the elastic and plastic strain at the ultimate tensile strength in the low-carbon steel...

See similar textbooks

Similar questions

Compound axial member ABC has a uniform diameter of d = 1.50 in. Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 80 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 112 in. When axial force P is applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 1700 pin./in. in longitudinal direction. What is the total elongation of member ABC? L2 (1) d Aluminum В (2) Сopper
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.58 in. and an elastic modulus of 2430 ksi. Bar (2) has a cross-sectional area of 0.714 in and an elastic modulus of 4110 ksi. Assume Ly-18 in., Lz-47in, Q=6,4 kips, P-3.2 kips, and R-128 kips. Determine the horizontal deflection of end Crelative to end A. (1) Answer: uCA in.
Narrow bars of aluminum are bonded to the two sides of a thick steel plate as shown. Initially, at T₁ = 70°F, all stresses are zero. Knowing that the temperature will be slowly raised to T₂ and then reduced to T₁, determine (a) the highest temperature T₂ that does not result in residual stresses, (b) the temperature T₂ that will result in a residual stress in the aluminum equal to 58 ksi. Assume aa = 12.8 x 10-6/°F for the aluminum and a = 6.5 × 10-6/°F for the steel. Further assume that the aluminum is elastoplastic with E = 10.9 × 106 psi and ay = 58 ksi. (Hint: Neglect the small stresses in the plate.) Fig. P2.121
A hollow aluminum tube is rigidly attached between steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in aluminum of 80 MPa, in steel of 150 MPa or bronze of 100 MPa. Steel Aluminum Bronze А P> ЗР - 2P outside = 30 mm d inside = 20 mm d d = 16 mm d = 60 mm -100mm- -150mm- -125mm-
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Find the maximum value of P in kN that will not exceed a stress in steel of 140 MPa, in aluminum of 90 MPa, or in bronze of 100 MPa
An aluminum alloy [E = 67 GPa; ν = 0.33; α = 23.0 × 10–6/°C] plate is subjected to a tensile load P. The plate has a depth of d = 225 mm, a cross-sectional area of A = 5100 mm2, and a length of L = 4.1 m. The initial longitudinal normal strain in the plate is zero. After load P is applied and the temperature of the plate has been increased by ΔT = 63°C, the longitudinal normal strain in the plate is found to be 2900 με. Determine: (a) the magnitude of load P. (b) the change in plate depth Δd.
STRAIN
An aluminum alloy [E = 72 GPa; v = 0.33; a= 23.0 x 10-6/°C] plate is subjected to a tensile load P. The plate has a depth of d = 245 mm, a cross-sectional area of A = 5500 mm², and a length of L = 6.0 m. The initial longitudinal normal strain in the plate is zero. After load P is applied and the temperature of the plate has been increased by AT = 69°C, the longitudinal normal strain in the plate is found to be 3340 μc. Determine: (a) the magnitude of load P. (b) the change in plate depth Ad. L P Answer: (a) P = i (b) Δd = i KN mm
An aluminum alloy [E = 73 GPa; v = 0.33; a= 23.0 x 10-6/°C] plate is subjected to a tensile load P. The plate has a depth of d = 250 mm, a cross-sectional area of A = 6900 mm², and a length of L = 5.9 m. The initial longitudinal normal strain in the plate is zero. After load P is applied and the temperature of the plate has been increased by AT = 50°C, the longitudinal normal strain in the plate is found to be 2400 με. Determine: (a) the magnitude of load P. (b) the change in plate depth Ad. L Answer: (a) P = i (b) Δd = KN mm
The bending stress in a beam is section modulus. O(A) Inversely proportional to two times O(B) Directly proportional to O(C) Inversely proportional to O(D) None of these
3) An bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPA, in aluminum of 90MPA or in bronze of 100MPа. Aluminum A = 500mm? Bronze A = 200mm? Steel A = 150mm2 2P ЗР L st = 1.2m L br = 2m Lal = 3.5m
Design of steel structures