Problem 2 The mechanical system consists of two identical steel rods (A = 30 mm2, E = 200GPA, a = 15x106/°C) and a "rigid" beam AC. The beam is supported by a smooth pin at B. The nuts at A and C are initially tightened just enough to remove the slack, leaving the two rods stress-free. 1- Determine the axial stresses induced in rods (1) and (2) if the temperature of both rods is decreased by 60°C. 2- Determine the (small) angle 0 through which the beam AC would rotate due to this temperature change. -200 mm 80 mm A В -"Rigid" |(1) (2) 250 mm

Problem 2 The mechanical system consists of two identical steel rods (A = 30 mm2, E = 200GPA, a = 15x106/°C) and a "rigid" beam AC. The beam is supported by a smooth pin at B. The nuts at A and C are initially tightened just enough to remove the slack, leaving the two rods stress-free. 1- Determine the axial stresses induced in rods (1) and (2) if the temperature of both rods is decreased by 60°C. 2- Determine the (small) angle 0 through which the beam AC would rotate due to this temperature change. -200 mm 80 mm A В -"Rigid" |(1) (2) 250 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

400mm Find the required spacing of intermediate stiffeners if V*=1600KN 25mm • Check the adequacy of a pair of stiffeners 90mmx12mm • Check the web crushing capacity if the reaction of 1600kN is applied over a stiff bearing length of 250mm at the end of the beam (note that the spread of stress can only go in one direction) • Homework extension: Check the adequacy of an endplate stiffener 300 wide by 16mm thick 12mm Use Grade 300 Steel 1440mm
The brass wire has a triangular cross section, 2mm on a side. The yield stress for brass is Ty= 208 MPa. Gbr= 37 GPa. Determine the maximum torque to which it can be subjected so that the wire will not yield and the angle of twist
H.W 3 Two aluminum alloy plates (2) are attached to the sides of a wooden beam (1) as shown in Figure 3. mensions of the composite cross section are b1 = 80 mm, d¡ = 240 mm, b2 = 10 mm, d2 = b2 The di- |di 120 mm, and a = 60 mm. Deter- (2) (2) %3D mine the maximum bending (1) a stresses produced in both the wooden beam and the aluminum b1 plates if a bending moment FIGURE 3 +6,000 N m is applied M2 %3D about the z axis. Assume that Ej = 12.5 GPa and E2 = 70 GPa.
The steel bar AB has a diameter of 30mm and is connected to the brass bar BC. The two bars are fixed to unyielding supports at the top (point A) and bottom (point C) ends. If there is a temperature rise of 50°C, calculate the compressive force induced in the rods (ABC). Note: For steel (E = 200 GPa, as = 11.7 x 106 °C) and for brass (E = 105 GPa, qb= 20.9 x 10-6/ °C). 250 mm 300 mm A B -30-mm diameter -50-mm diameter
Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 100 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 140 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 2300 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L2 (1) Aluminum B (2) Copper Answer: in, AL = i
Read the question carefully and give me solution according to the question... Give me both solution
H1
A magnesium-alloy rod (E = 6.5 x 10 ksi) of Prob. 3.4-6. diameter d 1 in. is encased by a brass tube (E 15 x 10 ksi) with outer diameter d. = 1.5 in.; both have length. L = 20 in. An axial load P = 10 kips is applied to the resulting bimetallic rod. (a) Determine the normal stresses and , in each material, assuming that the magnesium rod and brass tube are securely bonded to each other. (b) Determine the elongation of the bimetallic rod. P
А P 200 mm В E 150 mm F Three steel (E=200 GPa) rods (AB, CD and EF) support a load of P=30 kN as shown in the figure. Each of the rods AB and CD has a 80-mm2 cross-sectional area and rod EF has a 120-mm2 cross-sectional area. (a) Write the equilibrium equation for the rigid member BED in vertical direction, (b) write the compatibility equation for the given bar system, (c) determine the force in rod EF (d) determine the average normal stress in rod EF.
Subject: Static of rigid bodies Find: Shear Diagram of beam 1, 2, and 3. Show me the solution pls thank you!
Please show complete solution. Thank you!
A magnesium-alloy rod (E = 6.5 x 10 ksi) of Prob. 3.4-6. diameter d 1 in. is encased by a brass tube (E 15 x 10 ksi) with outer diameter d, = 1.5 in.; both have length L = 20 in. An axial load P = 10 kips is applied to the resulting bimetallic rod. (a) Determine the normal stresses and , in each material, assuming that the magnesium rod and brass tube are securely bonded to each other. (b) Determine the elongation of the bimetallic rod. P