Situation 2: A W10x30 has a length of 4.80 m. Fy = 248 MPa. The properties are given below. Properties of W shape A = 5,700 mm^2 d = 267 mm bf = 148 mm tf = 13 mm kdes = 7.62 mm tw 14.5 mm rx 111 mm ry=34.80 mm 1. Which of the following most nearly gives the axial capacity (Pa) of the column if both are fixed? O 660 KN O 641 KN O 667 KN O 600 KN

Situation 2: A W10x30 has a length of 4.80 m. Fy = 248 MPa. The properties are given below. Properties of W shape A = 5,700 mm^2 d = 267 mm bf = 148 mm tf = 13 mm kdes = 7.62 mm tw 14.5 mm rx 111 mm ry=34.80 mm 1. Which of the following most nearly gives the axial capacity (Pa) of the column if both are fixed? O 660 KN O 641 KN O 667 KN O 600 KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid frame shown in Figure is unbraced. The members are oriented so that bending is about the strong axis. Support conditions in the direction perpendicular to the plane of the frame are such that Ky = 1.0. The beams are W18 x 50, and the columns are W12 x 72. A992 steel is used. The axial compressive dead load is 50 kips, and the axial compressive live load is 150 kips. a. Determine the axial compressive design strength of column AB. Use the stiffness reduction factor if applicable. b. Determine the allowable axial compressive strength of column AB. Use the stiffness reduction factor if applicable.
A crate with a mass of 250 kg is held in equilibrium by three ropes attached to a steel ring. a d3 d₁ d5 B A 5.5 m 4 m d2 3.5 m 2m d₁ Z 3 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value d₁ 2 m d₂ d4 a. Determine the magnitude of the force/tension in cord A, TA. b. Determine the magnitude of the force/tension in cord B, TB. c. Determine the magnitude of the force/tension in cord C, Tc. Round your final answers to 3 significant digits/figures. The magnitude of the force/tension in cord A is The magnitude of the force/tension in cord B is The magnitude of the force/tension in cord C' is d5 kN kN kN
An A913 Gr. 60 W14x109 is used as a 15-m high column. The column is fixed at both ends and is laterally supported (hinged) at every one-third of its height about the weak axis. 1. Calculate the governing slenderness ratio of the column.2. Calculate the Euler Buckling stress, Fe in MPa.3. Determine the ultimate design strength, in kN
A high performance racing plane is to have an aileron control rod made out of unidirectional carbon fibre tubing with the following material properties: elastic modulus E = 90 GPa and compressive failure stress OF,comp= 600 MPa. In order to avoid parts of the internal wing structure the control rod is required to have a bend at the tip as shown in the figure. The rod is L = 400 mm long with an inner diameter of 8 mm and an outer diameter of 10 mm. The length of the bent portion of the rod is = 40 mm . The servo applies a maximum compressive or tensile force of F= 200 N on one end of the control rod as shown in the diagram. The end at which the loading is applied can be considered to be free and the other end of the control rod can be considered to be fixed. Consider the case where the servo applies a compressive force on the tip of the control rod: (i) (ii) X Find the maximum compressive stress in the rod and the maximum transverse deflection of the rod at B. Find the maximum…
P4: Calculate the design moment strength of the T-section shown in the following figure (fe' = 28 MPa and Fy = 420 MPa). 111 100 cm 3.5mm 3=22 350 E 3.25 m 250 3=22 3.25 250 m
3) The rigid horizontal bar AB is supported by three vertical rods as shown in the figure and carries the load of 110 kN. The system is stress free before the load is applied. After the load was applied, the temperature of all wires is raised by 20°C. Use a = 12x10-6/°C for steel, a = 18x10-6/°C for copper and a = 20x10-6/°C for brass. Neglecting the weight of the bar AB, determine the location of the 110 kN force in order that AB remains horizontal. copper bar: A=195mm? steel bar: brass bar: A=130mm? A=325mm? A C B 110 kN 3.00m 2.00m 1.80m _ 1.20m 1.50m
The aluminum W 310 x 202 (wide flange) column is subjected to an eccentric axial load P as shown. The maximum compressive stress in the column is given by the so-called secant formula: where --- [¹ + ( √5)] ec o 1+ sec max E ō = P/A = average stress A = 25800 mm² = cross-sectional area of the column e = 85 mm = eccentricity of the load c = 170 mm = half depth of the column r = 142 mm = radius of gyration of the cross section L = 7100 mm = length of the column E = 71 x 10⁹ Pa = modulus of elasticity Determine the maximum load P that the column can carry if the maximum stress is not to exceed 120 × 10^6 Pa. Terminate the computation when Σa < 0.0005%.
The 22-mm-diameter A-36 steel rod is subjected to the axial forces shown. Take E = 200 GPa. (Figure 1) Figure 1 A of 1 600 mm B 400 mm 50 kN 50 kN C 40 kN MILA Determine the displacement of end C with respect to the fixed support at A. Express your answer to three significant figures and include the appropriate units. 1 dc = Submit μÅ Value Units My Answers Give Up ?
A frame has dimensions and loadings as shown in the figure and parameter table. Determine the horizontal and vertical support reactions that the pins exert on the frame at A and C. Take postive directions to be to the right, and up. 080 BY NO SA 2021 Cathy Zupke parameter Force Ax Force Ay= Force Co = Force Cy= = W L₁ L2 A value 1 3 4.5 -L₂- units kN/m m m KN KN KN KN C B W
An elliptical gate covers the end of a pipe 4m in diameter. Of the gate is hinged at the top, what normal force F is required to open the gate when water is 8m deep above the top of pipe and the pipe is open to the atmosphere on the other side? Neglect the weight of the gate. Find: ħ in kPa Agate in m2 FR in kN ȳ in m I in m4 ycp in m F in kN
A steel rod (E = 200 GPa) is subjected to the load shown, where P = 2500 kN A gap a = 2.00 mm exists before the load is applied. The elongated rod contacts the top surface at C'. Assume the mass of the rod is negligible. The values for the figure below are d = 0.750 m, e = 0.400 m, j = 59.0 mm , and g = 44.0 mm. L. What is the Fc, Fa and ò cla ?
A 17-mm-diameter steel [E = 206 GPa; a = 11.5×10-6/°C] bolt is used to connect two rigid parts of an assembly. The bolt length is a = 130 mm. Determine the minimum clamping force that must be provided by the bolt when T₁ = 17°C so that the clamping force it exerts when T2 = 60°C is at least 2.1 kN. a Answer: F₁ = KN