Situation 1: A W8x67 has a length of 7.50 m. Fy= 248 MPa. The properties are given below. Properties of W shape A = 12,700 mm^2 d = 229 mm bf = 210 mm tf = 23.7 mm kdes 33.8 mm tw 14.5 mm rx = 94.5 mm ry = 53.80 mm 1. Which of the following most nearly gives the axial capacity (Pa) of the column if one end is fixed and the other is pinned connected? O 1143 KN O 1106 KN O 1058 KN

Situation 1: A W8x67 has a length of 7.50 m. Fy= 248 MPa. The properties are given below. Properties of W shape A = 12,700 mm^2 d = 229 mm bf = 210 mm tf = 23.7 mm kdes 33.8 mm tw 14.5 mm rx = 94.5 mm ry = 53.80 mm 1. Which of the following most nearly gives the axial capacity (Pa) of the column if one end is fixed and the other is pinned connected? O 1143 KN O 1106 KN O 1058 KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

i need the answer quickly
For the beam loaded as shown in figure, a) calculate the slope of the elastic curve over the right support b) calculate the slope of the elastic at midway between supports 240 lb 100lb/ft 50 lb-ft R1 R2 2'
An aluminum bar having a cross-sectional area of 0.8 in2 carries the axial loads applied at the positions shown in Fig. P-209. Compute the total change in length of the bar if E = 10 × 103.4 psi. Assume the bar is suitably braced to prevent lateral buckling. 1. Figure P-209 and P-210 7000 lb 5000 lb 6000 lb 4000 lb 3 ft 5 ft 4 ft
In the beam given below, it is subjected to a load of L= 3 m and a uniformly distributed load q=10 kN/m. Calculate the rotational value at point A based on the hand bending stiffness?
Shown in the figure attached is a beam. Given the loading and support condition and assuming that EI is constant for the beam, determine the (a) The equation of the elastic curve, (b) The deflection at the left end of the beam, and (c) The support reactions By and MB.
Situation 2: A W10x30 has a length of 4.80 m. Fy = 248 MPa. The properties are given below. Properties of W shape A = 5,700 mm^2 d = 267 mm bf = 148 mm tf = 13 mm kdes = 7.62 mm tw = 14.5 mm rx = 111 mm ry=34.80 mm 1. Which of the following most nearly gives the axial capacity (Pa) of the column if one end is fixed and the other is pinned connected? O 519 KN O 496 KN. O 534 KN O 511 KN
Determine the design strength of a T-Beam with the following data: b+= 700 mm bw = 300 mm hy = 100 mm d = 500 mm f₂ = 21 MPa fy = 414 MPa A: 5-20 mm dia.
Situation 4: A W6x25 has a length of 5.3 m. Fy = 248 MPa. The properties are given below. Properties of W shape A 4,740 mm^2 d = 162 mm bf 154 mm tf = 11.60 mm kdes 17.9 mm tw = 8.13 mm rx = 68.60 mm ry = 38.60 mm 1. Which of the following most nearly gives the axial capacity (Pu) of the column if one end is fixed and the other is pinned connected? O 651 KN O 600KN. O 680 KN O 633 KN
Number 9
statics rigid of bodies
A high performance racing plane is to have an aileron control rod made out of unidirectional carbon fibre tubing with the following material properties: elastic modulus E = 90 GPa and compressive failure stress OF,comp= 600 MPa. In order to avoid parts of the internal wing structure the control rod is required to have a bend at the tip as shown in the figure. The rod is L = 400 mm long with an inner diameter of 8 mm and an outer diameter of 10 mm. The length of the bent portion of the rod is = 40 mm . The servo applies a maximum compressive or tensile force of F= 200 N on one end of the control rod as shown in the diagram. The end at which the loading is applied can be considered to be free and the other end of the control rod can be considered to be fixed. Consider the case where the servo applies a compressive force on the tip of the control rod: (i) (ii) X Find the maximum compressive stress in the rod and the maximum transverse deflection of the rod at B. Find the maximum…
P4: Calculate the design moment strength of the T-section shown in the following figure (fe' = 28 MPa and Fy = 420 MPa). 111 100 cm 3.5mm 3=22 350 E 3.25 m 250 3=22 3.25 250 m