Situation 2: A W10x30 has a length of 4.80 m. Fy = 248 MPa. The properties are given below. Properties of W shape A = 5,700 mm^2 d = 267 mm bf 148 mm tf = 13 mm kdes 7.62 mm tw = 14.5 mm rx = 111 mm ry=34.80 mm 1. Which of the following most nearly gives the axial capacity (Pa) of the column if one end is fixed and the other is pinned connected? Ⓒ519 KN O 496 KN. O 534 KN O 511 KN

Situation 2: A W10x30 has a length of 4.80 m. Fy = 248 MPa. The properties are given below. Properties of W shape A = 5,700 mm^2 d = 267 mm bf 148 mm tf = 13 mm kdes 7.62 mm tw = 14.5 mm rx = 111 mm ry=34.80 mm 1. Which of the following most nearly gives the axial capacity (Pa) of the column if one end is fixed and the other is pinned connected? Ⓒ519 KN O 496 KN. O 534 KN O 511 KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 2: A W10x30 has a length of 4.80 m. Fy = 248 MPa. The properties are given below. Properties of W shape A = 5,700 mm^2 d = 267 mm bf = 148 mm tf = 13 mm kdes = 7.62 mm tw = 14.5 mm rx = 111 mm ry=34.80 mm 1. Which of the following most nearly gives the axial capacity (Pa) of the column if both are fixed? O 660 KN 641 KN 667 KN O 600 KN
Situation 1: A W8x67 has a length of 7.50 m. Fy = 248 MPa. The properties are given below. Properties of W shape A = 12,700 mm^2 d = 229 mm bf = 210 mm tf = 23.7 mm kdes = 33.8 mm tw = 14.5 mm rx = 94.5 mm ry = 53.80 mm 1. Which of the following most nearly gives the axial capacity (Pa) of the column if both are pinned? O 678 KN O 667 KN O 740 KN O 652 KN
Compute the area of steel for the L-section shown in the figure if it is subjected to M₁ = 120 kN.m feu = 35 N/mm² and fy = 400 N/mm² 400 mm 600 mm 120 mm 100 T IS456
Determine the design strength of a T-Beam with the following data: b+= 700 mm bw = 300 mm hy = 100 mm d = 500 mm f₂ = 21 MPa fy = 414 MPa A: 5-20 mm dia.
The rigid bar AB, attached to two vertical rods as shown in the figure, is horizontal before the load is applied. If the load P = 50 kN, determine its vertical movement. STEEL L=3 M A= 300 mm² E= 200 GPa 2m зм P= 50 KN ALUMINUM L=43 A== 1500 mm² E-7067.
The A992 steel W200 x 46 member shown in Figure . is to be used as a pin-connected column. Determine the largest axial load it can support before it either begins to buckle or the steel yields. Given: A = 5890 mm? Ix =45.5 (10) mm ly = 15.3 (106) mm %3D 3 m
Determine the design strength of a T- Beam given the following data: b = 700 mm by = 300 mm hf = 100 mm d = 500 mm fe' = 21 MPa fy = 414 MPa As: 5- 20 mm dia.
Please write the words clearly A horizontal bar AB is supported by a pinned-end column CD as shown in the figure. The column is a steel hollow circular section (E = 210 GPa) having length Q2. %3D of 4 m. The inside diameter and the outside diameter of the section is 80 mm and 100 mm. Calculate the allowable load Q if the factor of safety with respect to buckling of the column isn = 2.5. KIm> 2m A В 4m.
The assembly consists of three titanium (Ti-6A1-4V) rods and a rigid bar AC. The cross-sectional area of each rod is given in the figure. If a force of 60 kip is applied to the ring F, determine the horizontal displacement of point F.
STEEL DESIGN PROBLEM: USE NSCP 2015 IN SOLVING THE PROBLEM BELOW. A W310 x 117 column which is an A992 steel is carrying a dead load of 2490 kN and a live load of 300 kN. The support conditions is having one end fixed and the other end pinned. The column has a length of 6 meters. Ag = 15,000 mm^2; rx=136 mm; ry=77.5mm. 1. What is the required design strength of the section due to Flexural Buckling? 2. Is the section adequate to carry the required load? 3. What is the critical buckling stress (in MPa) of the section?
PROBLEM SET Situation 1 The rigid bar AB, attached to two vertical rods as shown in the figure, is horizontal before the load is applied. If the load P=50 KN. Compute the vertical movement under the load. Aluminum E«70 GPa Steel L-4m E-200 GPa A=500 mm? L-3m A-300 mm 2 m
Please show solutions on how to get the 27.57 value. The circle green in the figure. Civil engineering- steel design Note: I thought the value is 86.617 . Feel free to correct me . What should put in circle in the figure.