3) The rigid horizontal bar AB is supported by three vertical rods as shown in the figure and carries the load of 110 kN . The system is stress free before the load is applied. After the load was applied, the temperature of all wires is raised by 20°C. Use a = 12x10-6/°C for steel, a = 18x10-6/°C for copper and a = 20x10-6/°C_for brass. Neglecting %3D the weight of the bar AB, determine the location of the 110 kN force in order that AB remains horizontal. yus brass bar: copper bar: A=195mm? steel bar: A=130mm? A=325mm? A B 110 kN 3.00m 2.00m 1.80m 1.20m 1.50m

3) The rigid horizontal bar AB is supported by three vertical rods as shown in the figure and carries the load of 110 kN . The system is stress free before the load is applied. After the load was applied, the temperature of all wires is raised by 20°C. Use a = 12x10-6/°C for steel, a = 18x10-6/°C for copper and a = 20x10-6/°C_for brass. Neglecting %3D the weight of the bar AB, determine the location of the 110 kN force in order that AB remains horizontal. yus brass bar: copper bar: A=195mm? steel bar: A=130mm? A=325mm? A B 110 kN 3.00m 2.00m 1.80m 1.20m 1.50m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

need fast
The solid rod has a diameter of 20mm. Find the following: Angle of twist at C with respect to A (in radians) Angle of twist at B with respect to A (in radians) Maximum shear stress at A (in MPa) (Shear stress at support, at a point 7mm from center. (in MPa) A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C
a uniform bar 1 is connected to a tapered rod 2. both are subjected to axial loads as shown. if P=7 kN, determine the axial deformation of tapered rod 2 (in mm). indicate negative sign if compression
STATICS OF RIGID BODIESI NEED HELP ASAP. Please read and answer the question correctly. RATE WILL BE GIVEN ACCORDINGLY. THANK YOU EXACT ANSWER Note: The tolerance is ± 1 in the third significant digit This is a by parts question so please answer all possible question.
A high-density polyethylene [E = 135 ksi and a = 69 x 10-6/°F) block (1) is positioned in a fixture. The block is 2.1 in, by 2.2 in. by 36 in. long. At room temperature, a gap of 0.1 in. exists between the block and the rigid support at B. Assume L₁- 36 in and A = 0.1 in. Determine: (a) the normal stressa in block (1) caused by a temperature increase of 70°F. (b) the normal strain e in block (1) at the increased temperature. Answers: (a) a = (b) = i B 277.05 A LA psi. pc.
3.2 The rigid bar of negligible weight is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises by 20∘C after a load W = 110 kN is applied.
A mild steel flat of width 120 mm and thickness 10 mm is bent into an arc of a circle of radius 10 m by applying a pure moment 'M'. If E is 200 GPa, then magnitude of the pure moment 'M' will be
Q19: In Figure below, what is the ratio of P to F h Waer Hinge Sec A-A
Step by step solution *