The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 390 mm tw = 12 mm d - 100 mm t = 6.4 mm Additionally: • The area of each pipe is A = 1882 mm². • The moment of inertia of the entire beam cross section about the z centroidal axis is Iz= 171660000 mm4. If the beam will be subjected to a shear force of V = 120 kN, determine the shear stress at point H, located at y = 100 mm above the z centroidal axis. H Hy K Answer: Z MD- Ун YK K ily h

The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 390 mm tw = 12 mm d - 100 mm t = 6.4 mm Additionally: • The area of each pipe is A = 1882 mm². • The moment of inertia of the entire beam cross section about the z centroidal axis is Iz= 171660000 mm4. If the beam will be subjected to a shear force of V = 120 kN, determine the shear stress at point H, located at y = 100 mm above the z centroidal axis. H Hy K Answer: Z MD- Ун YK K ily h

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The figure shows a cutaway view of an assembly in which a solid bronze [G= 6,500 ksi] rod (1) is fitted inside of an aluminum alloy [G = 4,000 ksi] tube (2). The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at A. The rod diameter is d₁ = 1.55 in. The outside diameter of the tube is D₂ = 2.8 in. and its wall thickness is t₂ = 0.115 in. Overall dimensions of the assembly are a = 35 in. and b = 11 in. The allowable shear stresses for the bronze and aluminum materials are 9800 psi and 8500 psi, respectively. Further, the rotation angle of end B must be limited to a magnitude of 4.2°. Based on these constraints, what is the maximum torque Tg that can be applied at end B? Fixed End plate plate di TB Rod (1) D₂ Answer: TB = A Tube (2) a lb-in b B
find the maximum bending moment and maximum deflection
B3
6
In the truss system shown in the figure below, there are totally nine bars. Pick any six of them and calculate the forces they are bearing. Put your answers in the table below. Show your analysis. E Force Compression/ Bar magnitude Tension 4 m 45° АВ AC A 7 m AD 90 BD 3 m 90° CD CF B F CE 4 m 4 m DF 30 N FE
А L B 425 mm C 1,000 mm V P A steel bar (1) and an Aluminum bar (2) are connected to a rigid angle ACD. Assuming: • Steel [E = 200 GPa] bar (1) is 6mm x 40mm x 600mm long. • Aluminum [E = 70 GPa] bar (2) is 10mm x 40mm x 600mm long. Poisson's ratio, v = 0.35 • A distance L of 500mm. a)Determine the force P (in kN) required to stretch the Aluminum bar by 1mm. Enter the force, P, into the d21 answer box (in kN, 3 sig digs). b) Determine the final width and thickness of the Aluminum bar. (1) Your Answer:
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 470 mm tw = 14 mm d = 120 mm t = 9.6 mm Additionally: • The area of each pipe is A = 3330 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is IZ = 428040000 mm4. If the beam will be subjected to a shear force of V = 225 kN, determine the shear stress at point H, located at yH = 110 mm above the z centroidal axis.
Determine the force in each member of the loaded truss. The force is positive if in tension, negative if in compression. AB= 31° 59 Answers: BC= 10 B 218 kg i 1870 AC = i -1870 i -1120 N Z Z Z N N
A pump is driven from an engine crank-shaft by the mechanism as shown in Figure . The pump piston shown at F is 250 mm in diameter and the crank speed is 100 r.p.m. The dimensions of various links are as follows: OA = 150 mm ; AB mm; DE = 500 mm. Determine for the position shown: 1. The velocity of the cross-head E, 2. The rubbing velocity of the pins A and B which are 50 mm diameter. 3.The acceleration of the cross-head E. 45 A 300 600 mm ; BC = 350 mm ; CD = 150 %3D 450 100 1111 All dimensions in mm.