Situation 2: A square hollow steel strut of thickness 10 mm is pin connected to two connector plates of thickness, 12 mm. The connector plates are welded to the base plate of thickness, 12mm. The base plate is fastened to the concrete base by 4-16 mm diameter anchor bolts. The diameter of the pin is 16 mm. 48 kN 4. Which of the following most nearly gives the bearing stress between the strut and the pin? a. 150 MPa steel strut c. 120 MPa b. 140 МPа d. 125 MPa 30 5. Which of the following most nearly gives the shearing stress in the pin? c. 103.37 MPa d. 119.37 MPa a. 110.46 MPa ь. 126.39 МPа base 6. Which of the following most nearly gives the shearing stress in the anchor bolts? c. 51.69 MPa d. 47.16 MPa plate a. 55.04 MPa b. 59.68 MPa connector plate anchor bolt

Situation 2: A square hollow steel strut of thickness 10 mm is pin connected to two connector plates of thickness, 12 mm. The connector plates are welded to the base plate of thickness, 12mm. The base plate is fastened to the concrete base by 4-16 mm diameter anchor bolts. The diameter of the pin is 16 mm. 48 kN 4. Which of the following most nearly gives the bearing stress between the strut and the pin? a. 150 MPa steel strut c. 120 MPa b. 140 МPа d. 125 MPa 30 5. Which of the following most nearly gives the shearing stress in the pin? c. 103.37 MPa d. 119.37 MPa a. 110.46 MPa ь. 126.39 МPа base 6. Which of the following most nearly gives the shearing stress in the anchor bolts? c. 51.69 MPa d. 47.16 MPa plate a. 55.04 MPa b. 59.68 MPa connector plate anchor bolt

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.1P

See similar textbooks

Similar questions

Item 2 Figure 1 A D of 1 -0.5 m- 400 KN B -0.5 m C 0.4 m Part A The assembly consists of two posts AD and CF made of A-36 steel and having a cross-sectional area of 1100 mm², and a 2014-T6 aluminum post BE having a cross-sectional area of 1700 mm². If a central load of 400 kN is applied to the rigid cap, determine the normal stress in each post. There is a small gap of 0.12 mm between the post BE and the rigid member ABC. (Figure 1) Enter your answers, separated by commas. JAD, CF, OBE = Submit O Π| ΑΣΦ ↓↑ My Answers Give Up vec ? MPa Provide Feedback Continue
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
The rectangular doubly reinforcement stress concrete block with the arrangement of reinforcement of 2N28 bars on top and 3N28 bars on bottom. The modulus of elasticity are Ec =23,500MPa and Es = 200,000MPa. Dead load is 18KN/m and live load is 12KN/m. f'c = 25MPa 800 730 N12 ligs (fx.t-500MPa) Ast = 3N28 350 Span = 10m Figure 3 Use the Transformed section approach considering the presence of steel. Calculate the concrete area and transformed steel area in both tension and compression shown in Figure 3. n=Es/Ec Ast=1232mm^2 Use n-1 for the transformed area to do the calculate. Unit: mm^2 with two decimal
Please kindly give me a,b,c and d answers..help me. Urgent Thank you
The center post B of the assembly has an original length of 124.7 mm, whereas postsA and C have a length of 125 mm. If the caps on the top and bottom can beconsidered rigid, determine the average normal stress in each post. The posts aremade of aluminum and have a cross-sectional area of 400 mm Eal = 70 GPa. Detailed solution pls. Thank you!
Question 8 1 p The rectangular doubly reinforcement stress concrete block with the arrangement of reinforcement of 2N28 bars on top and 3N28 bars on bottom. The modulus of elasticity are Ec=23,500MPa and Es = 200,000MPa. Dead load is 18KN/m and live load is 12KN/m. f'c = 25MPa 800 TE 730 N12 ligs (fsv.t-500MPa) Ast = 3N28 350 Span = 10m Figure 3 Calculate the concrete stresses in tension and compression of the reinforcement concrete beam shown in Figure 3. Compression concrete stress Choose ] Tension Concrete stress Choose]
The rectangular doubly reinforcement stress concrete block with the arrangement of reinforcement of 2N28 bars on top and 3N28 bars on bottom. The modulus of elasticity are Ec =23,500MPa and Es = 200,000MPa. Dead load is 18KN/m and live load is 12KN/m. f' = 25MPa 800 IDE 730 N12 ligs (fsv.f-500MPa) Ast = 3N28 350 Span = 10m Figure 3 Calculate the combination load for the reinforcement concrete beam shown in Figure 3. Unit: KN/m with two decimal. 1.2G+1.5Q=w
Subject: Steel design- Bolted Steel Connection *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten A plate having a width of 400 and a thickness of 20mm is to be connected to two plates with thickness of 12mm by four rivets. The allowable shear stress for the rivets is 150 MPa and for bearing is 1.35 Fy. If the yield strength and the ultimate strength is 248 MPa and 400 MPa respectively. Determine the Following: a.) Required diameter of rivets w/o exceeding the aloowable stress in the shear. b.) Required diameter of rivets w/o exceeding the allowable stress in bearing. c.) Required diameter of rivets w/o exceeding the allowable stress in tension.
can someone help me with this? Thank you
A flexural member is fabricated from two flanges plates 1/2" x 18" and a web plate 5/16" x 20". The yield stress of the steel is 36 ksi. a. Compute the elastic modulus and the yield moment with respect to major principal axis. b. Compute the plastic modulus and the plastic moment with respect to major principal axis.
Connections Example: Calculate the strength of the single lap joint. The plates are made of 1"x4" wooden blocks with a 2" overlap. The glue can carry 125 psi in shear. The wood can carry an axial stress of 1000 psi. How much force P can the joint carry? Sketch and FBD P b a P
5. The rod bar shown has steel, brass, and aluminum sections. Axial loads are applied at cross sections A, B, C and D. The allowable stresses are 125 MPa in steel, 70 MPa in the brass, and 85 MPa in the aluminum. Assume that the allowable stresses are the same for tension (T) and compression (C). (a) Determine the diameter required for the brass bar. (b) Determine the required diameter for the steel bar. (c) Determine the required diameter for the aluminum bar. Express your answer in millimeters. Steel Brass C Aluminum B A 100 kN 85 kN 200 kN 215 kN 0.5 m 0.5 m 0.5 m