AW 12 x 65 column section shown in the figure is pinned at each end and has an additional support in the weak direction at a point 3.6 m from the top. Use X 5.2 m K 1 for both directions. C111JPG Properties of W 12 x 65 A 12323 mm2 x-134.11 mm ry -76.71 mm Fy-248 MPa Determine the design compressive strength (kN)

AW 12 x 65 column section shown in the figure is pinned at each end and has an additional support in the weak direction at a point 3.6 m from the top. Use X 5.2 m K 1 for both directions. C111JPG Properties of W 12 x 65 A 12323 mm2 x-134.11 mm ry -76.71 mm Fy-248 MPa Determine the design compressive strength (kN)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Help pls.Thankyou.
I need the answer as soon as possible
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 24 kips, w = 2.2 kips/ft, LAB = 4.2 ft, LBC = 4.2 ft, and Lcp = 15.8 ft. Determine the magnitude of the maximum bending stress in the beam. P B LAB LBC Answer: Omax tel i |C * ksi W LCD X
What is the axial stress in the bronze rod (in MPa)? 2m 3m 60 kN IS mm banzerod
1. The details of the cantilever beam are shown below. Use f'c = 28 MPa, fy = 415 MPa, and fyt = 275 MPa. Notes:• All dimensions are in millimeters.• Column reinforcement not shown for clarity• Column and beam are neither exposed to weather nor contact with the ground.• Analyze as singly reinforce beam only.• Neglect the weight of the beam.• Concrete isnormal weight and reinforcements are galvanized. d. What is the flexural capacity of the beam at face of support in kNm? e. What is theshear capacity of the beam at face of support in kN? f. What is the maximum Pu (kN) that can be applied at the free end of the beam consideringflexure and shear? g. What is the requiredminimum cut length (mm) of each stirrup? Roundyour answer to nearest safe25 mm.
Derive the maximum steel ratio and the recommended rteel ratio fe' O.856 fy Po-004 3 0.85 fc' pooos= 0-85
Dicuss one way shear
6- For a simply supported beam with b=300 mm and d=500 mm, if f = 63MPa, f, = 280 MPa and the net tensile strain is greater than 0.005, then the maximum steel ratio equal............ (a) 0.0406 (b) 0.0310 (c) 0.0287 (d) 0.0180 (e) None
Determine the length of tension anchorage required for the 36 mm diameter plain mild steel reinforcing bars in the canrilever of figuer below. The charactersitic material strengths are feu-30N/mm² and fy=250KN. The ultimate anchorage bond stress. Stress, fou-1.5N/mm² Anchorage length R25 bars
Combined Stresses Given Hollow Steel Section (HSS) that is 4"x6" and 1/2" thick, with axial and transverse loading shown, determine the total normal stress at a. The 5k load on the bottom of the beam b. At the mid-span in the middle of the beam C. At the 10k load on top of the beam 5k 10k A 5' 10' 5' B CENTROID 4" 5 k 3k 8k 6" 2' 6.25k 8.75k +6.25k SECTION +1.25k 'V" -8.75k +43.75k-ft. +31.25k-ft. 'M' 8k 5 k + tension P = Ok %3D
A beam has a class 3 web and a class 2 flange. When along the stress-strain diagram will it fail, and how? Remember how we define the classes. Make a sketch showing a W-section beam that hasfailedin this way. How can this be prevented?
A beam has an f'c = 5000 psi, fy = 60000 psi, reinforcement ratio = 0.0137. Which of the following is most likely true about the strain in the extreme tension steel? Use the tables posted to Canvas as needed (The ones in the back of the book). The strain is = 0.005