AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 19 kips, w = 3.8 kips/ft, LAB = 5.2 ft, LBc =5.2 ft, and LCD= 14.4 ft. Determine the magnitude of the maximum bending stress in the beam.%3DDBLABLBCLCDAnswer:ksiOmax

Given Data: W18*40 Steel shape P=19 kips w=3.8 kips/ft LAB=LBC=5.2 ft LCD=14.4 ft It is asked…

AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P- 19 kips, w-3.8 kips/ft, LAB - 5.2 ft, Lac- 5.2 ft, and Lcp-14.4 ft. Determine the magnitude of the maximum bending stress in the beam. C LAB LBC LCD

AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P- 19 kips, w-3.8 kips/ft, LAB - 5.2 ft, Lac- 5.2 ft, and Lcp-14.4 ft. Determine the magnitude of the maximum bending stress in the beam. C LAB LBC LCD

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.2.1P

See similar textbooks

Related questions

Q: AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P= 27 kips, w…

A: Given:- A W18×40 standard steel shape beam is used to support load The magnitude of the point load =…

Q: A W18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 29 kips,…

A: Answer We know that maximum bending stress occur in a beam at extreme fibres and it can be…

Q: Justify the selection of a standard steel rolled section for the following Column from a bending…

A: M= 200.7 x 103 KNm σ = 175N/mm2 σsafe = σ/1.2 = 145.83 N/mm2

Q: The three suspender bars are made of A992 steel and have equal cross-sectional areas of 450mm².…

A: 3 suspended bars are given, of equal cross-sectional area as shown in the figure above and it has…

Q: Consider the girder and the moving loads shown in (Figure 1). Suppose that P= 101 kN. A 6 m C 10 mi…

Q: A steel beam is reinforced by three steel rods. The modulous of elasticity for concrete is 20Gpa and…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: a. Nominal moment capacity of the overhanging portion of the section. b. Depth of the compression…

A: Solution: Givendata: bf = 750 mm tf = 50 mm d = 750 mm bw = 350 mm Mu = 816 kN.m fc' = 20.7 Mpa fy =…

Q: a. Compute the vertical deflection at midspan due to flexural deformations only. b. Compute the…

Q: Pls help me answer. Thank you.

A: Here's an analysis of the failure mode and the importance of horizontal stirrups in deep beams:Deep…

Concept explainers

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.

Question

AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 19 kips, w = 3.8 kips/ft, LAB = 5.2 ft, LBc =
5.2 ft, and LCD= 14.4 ft. Determine the magnitude of the maximum bending stress in the beam.
%3D
D
B
LAB
LBC
LCD
Answer:
ksi
Omax

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 9 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
Determine the smallest value of yield stress Fy, for which a W-, M-, or S-shape from Part 1 of the Manual will become slender. To which shapes does this value apply? What conclusion can you draw from your answer?
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
Compute the nominal shear strength of an M1211.8 of A572 Grade 65 steel.
Estimate the transverse tensile strength of the concrete in Problem 12.6.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
Use the composite beam tables and select a W-shape and stud anchors for the following conditions: Span length = 18 6 Beam spacing = 9 ft Total slab thickness = 51 2 in. (the slab and deck combination weighs 57 psf). Lightweight concrete with a unit weight of 115 pcf is used Construction load = 20 psf Partition load = 20 psf Live load = 225 psf Fy=50 ksi and fc=4 ksi A cross section of the formed steel deck is shown in Figure P9.8-9. The maximum live-load deflection cannot exceed L/360 (use a lower-bound moment of inertia). a. Use LRFD. b. User ASD.
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are factored, and the uniformly distributed load includes a conservative estimate of the girder weight. Lateral support is provided at the ands and at the load points. Use LRFD for that following: a. Select the, flange and web dimensions so that intermediate stiffeners will he required. Use Fy=50 ksi and a total depth of 50 inches. Bearing stiffeners will be used at the ends and at the load points, but do not proportion them. b. Determine the locations of the intermediate stiffeners, but do not proportion them.
The given beam is laterally supported at the ends and at the 1 3 points (points 1, 2, 3, and 4). The concentrated load is a service live load. Use Fy=50 ksi and select a W-shape. Do not check deflections. a. Use LRFD. b. Use ASD.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
A beam is part of the framing system for the floor of an office building. The floor is subjected to both dead loads and live loads. The maximum moment caused by the service dead load is 45 ft-kips, and the maximum moment for the service live load is 63 ft-kips (these moments occur at the same location on the beam and can therefore be combined). a. If load and resistance factor design is used, determine the maximum factored bending moment (required moment strength). What is the controlling AISC load combination? b. What is the required nominal moment strength for a resistance factor of 0.90? c. If allowable strength design is used, determine the required moment strength. What is the controlling AISC lead combination? d. What is the required nominal moment strength for a safety factor of 1.67?