SCR used in to design of the single-phase inverter has the positive part eycle is double of the negative part, operating on 250V DC input, and delivering 50 Hz square-wave output voltage in the steady state. Load comprises an inductance 100 mH in series with 50 S2. Find: RMS values of two lowest order harmonics in output voltage. 78 V, and 46.8 V non 75 V,and 46.8 V O 78 V, and 45 V Peak value of the output current non 5.21 A 4.98 A 4.85 A

SCR used in to design of the single-phase inverter has the positive part eycle is double of the negative part, operating on 250V DC input, and delivering 50 Hz square-wave output voltage in the steady state. Load comprises an inductance 100 mH in series with 50 S2. Find: RMS values of two lowest order harmonics in output voltage. 78 V, and 46.8 V non 75 V,and 46.8 V O 78 V, and 45 V Peak value of the output current non 5.21 A 4.98 A 4.85 A

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

O d. 16W A Capacitor filter is used at the output across the load in order to minimize the ripple factor of the output voltage. The expressions of the average output voltage VDc and the output AC component VACare given below. If R = 1k2 and the single phase bridge rectifier supplied from a 120V - 50 Hz sinusoidal source, then the capacitor value that will maintain the amount of the output ripples to less than 4% would be equal to: VpC = Vm((4FRC – 1)/4fRC) VAC = Vm/(4/2fRC) Select one: a. 126.2uF O b. 93.39uF Oc. 63.39UF O d. 33.2uF TOSHIBA
The 3-phase half-wave diode rectifier feeds a load consisting of a 50-ohm resistor. The sinusoidal sources in the input of the rectifier are wye-connected and phase-to-phase rms voltage is 380 volts. Calculate the power (in watts) absorbed by the load. Assume the diode is ideal. a. 680.36 b. 2267.90 C. 4082.20 d. 1700.90 e. 1360.70
Question 2.a An ac power supply with VRMS =240 V and a full-wave rectifier are used to generate a de voltage for a resistive load with resistance value of 100 Q. The filter capacitor connected to the rectifier has capacitance value of 500 µF. The frequency of the ac supply is 50-Hz. Determine the de voltage and ripple factor at load side? а. Question 2.b Assume that by using an RC filter circuit, you wanted to reduce the ripple factor to half the amount that you calculated in part 2.a, answer the following questions: b. What values would you suggest for resistor and capacitor of the RC circuit? What is the voltage regulation of this circuit? с.
Find the performance parameters (FF, RF and 1) for the Single phase bridge uncontrolled rectifier with RL load. If the phase voltage: v,,(t) =V, sin(wt). Draw the circuit diagram and sketch the voltages and current waveforms.
Ex6 (H.W): A full-wave bridge rectifier supplies a load with 50 V dc, 100mA using 100 uF of filtering capacitor. Assume ideal diodes and Vs=Vsmax sin314 t, determine Vr(p.p), Vs max and Vs rms. s
: Find the average and rms values of the sinusoidal voltage measured at the output of full-wave rectifier.
What is the maximum value of vs(i.e.vsm ) Find the peak-to-peak ripple voltage vr Find the average output voltage Vo in steady state Find the average diode current ID in steady state. If the secondary winding resistance of the transformer is 1.5 Ω, calculate the maximum surge current in the worst-case scenario
Electrical Engineering _ Power Electronics Notes: pls try to answer in less than 30 min.
A PMMC instrument has internal resistance of 0.63 kQ and gives full scale deflection for 31 mA. The required resistance value of multiplier resistors for employing the meter as a multi range voltmeter for voltage range 64 V will be ohms. O a. 205.82 O b. -145.62 O c. 1434.52 O d. 101556.30
A battery is comprised of 4 cells connected in parallel, each cell has an EMF with 1.2V and an internal resistance of 0.55 ohm. There is no load connected to the terminals. Solve for Vterm.
A half-wave rectifier with a 270 2 load resistor operates from a 120 Vrms 60 Hz household supply current through a 3-to-1 step-down transformer. It uses a silicon diode that can be modelled as having a constant Vf = 0.84 V drop for any current. vs(t) VL (t) RL (a) What is the peak voltage, vs,peak, of the secondary? What is the peak voltage, UL,peak of the rectified output? (b) For what fraction of the cycle (in percentage) does the diode conduct? (c) What is the average output voltage, V₁? (state which formula you used: the more accurate formula obtained via integration or the approximate formula) 1 (d) What is the average output current, IL? (e) You want to create a DC source with a peak-to-peak ripple voltage, Vr, of 11% of the peak output. (1) What size of capacitor should you add across the output? (2) What is the average voltage now? (State whether you used the more accurate or the approximate formula.)
Draw a half-wave and full-wave rectifier circuit with 1 KQ load resistance andsketch the output waveforms when the input is 10 V sinusoidal signals. Also, findthe dc values for both the circuits.