For the circuit shown below D1 and D2 are Ideal Diodes, R1 = R2 = R33D2 K2. The output of the rectifier is shown below: a) Determine the VDC for the Vo = 10V without a capacitor. b) Sketch Vs (in the secondary).. c) Calculate the Value of the Capacitor required to produce Vr = 0.04V. d) Determine the Turn Ration of the transformer, for the input votage Vp = 120V. M. %3D 10V e) What is the PIV? D2 D1 T=20 ms Vp R1 R3 loN R2

For the circuit shown below D1 and D2 are Ideal Diodes, R1 = R2 = R33D2 K2. The output of the rectifier is shown below: a) Determine the VDC for the Vo = 10V without a capacitor. b) Sketch Vs (in the secondary).. c) Calculate the Value of the Capacitor required to produce Vr = 0.04V. d) Determine the Turn Ration of the transformer, for the input votage Vp = 120V. M. %3D 10V e) What is the PIV? D2 D1 T=20 ms Vp R1 R3 loN R2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Discuss the working principle of a diode and also the equivalent models of a diode.
Question 2) A full-wave rectifier with ohmic load given in the figure below feeds a 75 Q load and the effective (rms) value of the source voltage is 220V, its frequency is 50 Hz. Accordingly, find the following desired circuit parameters: a) the peak voltage of the source, b) the peak current of the load, c) Average stress of the load, d) Average current of the load, e) The effective (rms) voltage of the load, f) Effective (rms) current of the load, g) Power of the load i D2 vs R
In a full wave bridge rectifier, the transformer secondary voltage is 20sinwt. The forward resistance of each diode is 20N and load resistance is 1.5K. Calculate, i. Im ii. Ide
Please find the correct answer by solving the problem
Discussion: 1. Discuss the obtained curves. 2. What are the advantages of using cascade voltage regulator circuit? 3. To stabilize a voltage of 65 V, one can: a. Use one 65V zener diode b. Use ten 6.5 V zener diodes in series If the costs are irrelevant, then which solution is best and why?
A full-wave rectifier uses two diodes. The transformer r.m.s. secondary voltage from the center tap to each end of the secondary is 70 V and load resistance is 1000 0. Find: a) The mean load voltage and current b) The r.m.s. value of load current e) The PIV of the diode d) The efficiency of rectification
L, m, n is only needed pls
Please answer alll subparts i will like....
Q4/: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 10³t)] rms input signal has a load resistor of 3.3k2. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VL-P) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ? 4. What is the de voltage available at the load? 5. Explain who could filtering output signal. 6. Draw circuit that give opposite out waveform. 7. Why connect circuit in this form.
A full-wave bridge rectifier with a 100V rms sinusoidal input has a load resistor of 1 k. a. If silicon diodes are employed, what is the de voltage available at the load? b. Determine the required PIV rating of each diode. c. Find the maximum current through each diode during conduction. D.
5. The bridge rectifier shown in Figure 2 uses ideal diodes. The input voltage is 24V. Find: a. DC output voltage b. Sketch the output waveform D2 D3 R1 = 12 k2 Da D Figure 2. Circuit for problem 5 and 6 6. If the bridge rectifier shown in Figure 2 is modified using silicon diodes, find: a. dc output voltage b. sketch the output waveform ell ll
For a full wave controlled rectifier with pure resistive load (R=100),the supply voltage is (V-50Sin314t). When the firing angle (a =0%) determine the followings: 1) The mean (dc) value of the load current. 2) The RMS value of the load voltage.