8.* A single phase bridge rectifier supplies a 1kW washing machine induction motor drive. The smoothing capacitance is 6.8 mF and the smoothing inductance is 5 mH. At full load, the equivalent resistance of the induction motor is 24 2. The ac supply is 220 V (60Hz). (a) (b) (c) Estimate the ripple What is the capacitor 'de link' voltage under full load? What is the % voltage regulation no load to full load?

8.* A single phase bridge rectifier supplies a 1kW washing machine induction motor drive. The smoothing capacitance is 6.8 mF and the smoothing inductance is 5 mH. At full load, the equivalent resistance of the induction motor is 24 2. The ac supply is 220 V (60Hz). (a) (b) (c) Estimate the ripple What is the capacitor 'de link' voltage under full load? What is the % voltage regulation no load to full load?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

5. For the transformer coupled half- wave rectifier circuit shown below: detei peak secondary voltage of the transformer 4:1 120V, 60H3 R. 2.5KL
Question-3 Can you throw the emergency solution? I would appreciate it if you write legibly.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D1 IN4001 RL out OV 10 kN IN4001 alll
i need the answer quickly
Please answer ASAP for like this
Q2) A 3-phase, half-wave thyristor converter is connected through a voltage source 150 V as input voltage and used to supply resistive load of 10 2. Determine rsm voltage, rms current, ripple factor and dissipated power in the resistor R. If a = 45° and f = 50 Hz. %3D
A step down de chopper is connected to an R5 2 and L-10 mH. The de supply voltage is 100 V. The chopper is switching at a frequency of 1 kHz with a duty cycle of 50%. Determine the load current, lo and the peak to peak ripple current as an absolute value and as percentage of de value.
For the CRO square voltage waveform is shown in Figure. The 'time/cm' switch is on 5 ms/cm and the 'volts/cm' switch is on 2 V/cm. Calculate (a) the periodic time, (b) the peak to peak voltage, (c) the maximum voltage, (d) the time taken to complete half cycle The periodic time The peak to peak voltage The maximum voltage The time taken to complete half cycle
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R1, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D IN4001 R1 V out 10 kN D2 IN4001 allle
4- Single phase centre-tape rectifier with 100V peak secondary voltage per coil, energizing 10 Ohms and 2mH inductance with 50Hz source. The output rectified voltage drops to .of the Vdc. * 96% 98% 2.5%
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R1, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) DI 14001 RL V onl O V 10 kN D2 IN4001 allle