Question 5 A steel column with a rectangular hollow section is subject to a vertical downward load P1 and a horizontal load P2, as shown in Figure 5 below. If the width of the hollow section is 70mm and the thickness is 5mm, determine the maximum compressive stress at the base of the column. P1=500KN, P2=100kN. P1 - P2 e =110mm Top plate P2 P1 Im 120mm 120mm 3D (b) Top view showing location of loads (a) Column elevation 1.

Question 5 A steel column with a rectangular hollow section is subject to a vertical downward load P1 and a horizontal load P2, as shown in Figure 5 below. If the width of the hollow section is 70mm and the thickness is 5mm, determine the maximum compressive stress at the base of the column. P1=500KN, P2=100kN. P1 - P2 e =110mm Top plate P2 P1 Im 120mm 120mm 3D (b) Top view showing location of loads (a) Column elevation 1.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

6.59 A square section as shown in the figure below is subjected to bending moment M. (c) Obc = Obl y || h y H What is the maximum bending stress? (a) Obc = obt 12M h³ 9M 2h³ JXC h (b) bc = Obt = (d) %bc =%bt = 6M 4³ 9M h³
The wide-flange pinned-end column shown in the figure carries two loads, a force acting at the centroid P₁ = 450kN and a force P₂ = 270kN acting at distance s = 100 mm, from the centroid. The column is an HE 240B shape with L = 4.2m, E = 200 GPa, and Oy = 290 MPa. (a) What is the maximum compressive stress in the column?
A simple pin-connected truss is loaded and supported as shown. The load Pis 240 kN. All members of the truss are aluminum pipes that have an outside diameter of 130 mm and a wall thickness of 14 mm. Determine the normal stress in each truss member. Assume truss dimensions of a = 10 m, b = 6.25 m, and c= 5 m. Tensile stress is positive, while compressive stress is negative. b D Answer: OAB 11 JAC OBC= OBD = OCD = i M M a B MPa MPa MPa MPa MPa
Question 5 A steel column with a rectangular hollow section is subject to a vertical downward load P1 and a horizontal load P2, as shown in Figure 5 below. If the width of the hollow section is 70mm and the thickness is 5mm, determine the maximum compressive stress at the base of the column. P1=500KN, P2=100kN. P1 - P2 e =110mm Top plate- P2 P1 1m L120mm 120mm (b) Top view showing location of loads (a) Column elevation Figure 5: The cantilever column is fixed at the base.
Determine the maximum tensile stress in the beam shown.
6.59 A square section as shown in the figure below is subjected to bending moment M. (c) Obc = Obl y || h y H What is the maximum bending stress? (a) Obc = obt 12M h³ 9M 2h³ JXC h (b) bc = Obt = (d) %bc =%bt = 6M 4³ 9M h³
The aluminum W 310 x 202 (wide flange) column is subjected to an eccentric axial load P as shown. The maximum compressive stress in the column is given by the so-called secant formula: where --- [¹ + ( √5)] ec o 1+ sec max E ō = P/A = average stress A = 25800 mm² = cross-sectional area of the column e = 85 mm = eccentricity of the load c = 170 mm = half depth of the column r = 142 mm = radius of gyration of the cross section L = 7100 mm = length of the column E = 71 x 10⁹ Pa = modulus of elasticity Determine the maximum load P that the column can carry if the maximum stress is not to exceed 120 × 10^6 Pa. Terminate the computation when Σa < 0.0005%.
Q4 (b) Figure Q4(a) shows a steel beam with length of 4 m that is supported by a steel column at point B. The steel column of AB has a rectangular cross section (40 mm× 70 mm). The ends are assumed to be pin connected. The yield stress of steel is o y 250 MPa. The Modulus Elasticity of the steel is 200 GPa. Use factor of safety of 1.5. (i) Check whether the Euler's equation is appropriate or not. (ii) Determine the maximum distributed load (W) that can be applied to the beam so that the column of AB does not buckle.
For the beam shown in Figure (1), determine: a) The stresses in rods AB and BC. The cross-sectional area of rod AB is 155 mm2, and for BC is 200 mm?. b) The average shear stress in bolt at pin A. 1500 N S5 15 m 600 N/mt m- -3 m- Figure (1)
The beam is subjected to a loading condition as shown in th figure. Determine the (a) maximum tensile stress and (b) maximum compressive stress with the givenm cross section. Show you complete solution and diagram.
The general stress element shown is loaded such that o = 20 MPa, oy = -20 MPa, Txy = 10 MPa. What is the max dy 1 xy 70x