Learning Goal:The member shown is subjected to a compressivestress in the x direction of o₂ = 400 ksi and acompressive stress in the y direction of oy = 700 ksiThe dimensions of the member are a = 3.75 in, b =1.50 in, and t = 0.75 in. Assume that E - 29000 ksiand that Poisson's ratio is v= 0.29.(Figure 1)FigureVo91 of 1▼ Part D - Change in dimension of the memberThe applied stresses cause the member to experience a change in all of its dimensions. What are the new dimensions, d', b', and t', of themember due to the applied stresses?Express your answers in inches to three significant figures separated by commas.► View Available Hint(s)d', b',t' =Submit==Provide Feedback175) ΑΣΦΠΨΓ41 vec→ 0in, in, inNext >10:55 PM

Answered: Image /qna-images/answer/7a115181-170f-462e-a434-84ac225e1628.jpg

arning Goal: me member shown is subjected to a compressive ress in the x direction of a = 400 ksi and a mpressive stress in the y direction of ay = 700 ksi dy e dimensions of the member are a = 3.75 in. b = 50 in, and t = 0.75 in. Assume that E - 29000 ksi nd that Poisson's ratio is v=0.29.(Eigure 1) gure a b 0₂ 1 of 1 > P TH FEE m E: Provide

arning Goal: me member shown is subjected to a compressive ress in the x direction of a = 400 ksi and a mpressive stress in the y direction of ay = 700 ksi dy e dimensions of the member are a = 3.75 in. b = 50 in, and t = 0.75 in. Assume that E - 29000 ksi nd that Poisson's ratio is v=0.29.(Eigure 1) gure a b 0₂ 1 of 1 > P TH FEE m E: Provide

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Maximum allowable (safe) bending stress for a beam AB under a constant distributed load as shown in the figure.It is 40 MPa.a) What is the maximum value of the length (L) of the beam in this case?b) Draw the shear stress (τ) profile where the V (shear in section) force is greatest.Hint: You can specify several points in the section and calculate the shear stress for those points.
Compute for the maximum allowable distributed load o that can be applied to the simply supported beam as shown in Figure M-Va. The beam's cross section is detailed in Figure M-Vb. @(N/m) Allowable Stresses: Fiber Stress = +13.5 MPa / -12 MPa Transverse Shear Stress at NA = 900 kPa Transverse Shear Stress at Junction 800 2 m Figure M-Va 2 m Draw the flexural and shear stress distributions of the cross section. T 40 40 40 Figure M-Vb 40 120 mm
Mechanics I need the answer asap
3. The bar shown in Figure Q4 is subjected to tensile load of 160 kN. IIthe stress is the middle portion is limited to 150 N/mm', determine the diameter of the middle portion. Find also the length of the middle portion if the total elongation of the har is to be (0.2 mm. Young's modulus is given as equal to 2. 1x 10 N/ mm. 160 EN 40 cm Figure 04
Can you solve this questions?
Part A The stress at a point is shown on the element. Suppose that o, = 105 MPа, т - 158 MPа Determine the principal stress. (Figure 1) Enter your answers numerically using three significant figures separated by commas. VG AEo t vec ? Omax, Oint, Omin = MPа Submit Request Answer Part B Determine the absolute maximum shear stress. Express your answer with three significant figures and use the appropriate units. HA O ) ? Figure 1 of 1 > Value Units Timax in-plane = Submit Request Answer Provide Feedback
A beam with a T-section is supported and loaded as shown in the figure. The cross section has width b = 2 1/2 in., height h = 3 in., and thicknesst =3/8 in.(a) Determine the maximum tensile and compressive stresses in the beam.(b) If the allowable stresses in tension and compression are 18 ksi and 12 ksi, respectively, what is the required depth h of the beam? Assume thatthickness t remains at 3/8 in. and that flange width b 5 2.5 in.(c) Find the new values of loads P and q so that the allowable tension (18 ksi) and compression (12 ksi) stresses are reached simultaneously forthe beam. Use the beam cross section in part (a) (see figure) and assume that L1, L2, and L3 are unchanged.
Answer number 1 only
Question 2. The square plate ABCD is deformed into the shape shown by the dashed lines. If DC has a normal strain Ex = 0.005, DA has a normal strain ey = 0.004 at D, Yxy = 0.01rad determine the shear strain at point E with respect to the x' and y' axes. 600 mm- 600 mm E D
A simple pin-connected truss is loaded and supported as shown. The load P is 160 kN. All members of the truss are aluminum pipes that have an outside diameter of 130 mm and a wall thickness of 9 mm. Determine the normal stress in each truss member. Assume truss dimensions of a = 6 m, b = 3.75 m, and c = 3 m. Tensile stress is positive, while compressive stress is negative. b D A Answer: OAB OAC = OBC OBD OCD || || II a MPa MPa MPa MPa MPa B C
I need the answer as soon as possible
Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum tensile bending stress will occur at point C. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner C does not exceed 205 MPa. Answer: M- eTextbook and Media Save for Later Part 3 8.31E1 Answer: M-i The z-component of moment M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum compressive bending stress will occur at point A. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner A does not exceed 205 MPa. eTextbook and Media Save for Later Part 4 kN-m * Your answer is incorrect. kN-m Submit Answer Determine the maximum bending moment that can be applied to this cross…