6.59 A square section as shown in the figure below issubjected to bending moment M.(c) Obc = Obly||hyHWhat is the maximum bending stress?(a) Obc = obt12Mh³9M2h³JXCh(b) bc = Obt=(d) %bc =%bt =6M4³9Mh³

Given figure: Subjected to bending moment.

6.59 A square section as shown in the figure below is subjected to bending moment M. H (a) Obc = Obt = What is the maximum bending stress? 12M h³ (c) Ohr = Oh y || h 9M 7 (b) Obc = Obt (d) pc = Obl = 6M h³ 9M 3

6.59 A square section as shown in the figure below is subjected to bending moment M. H (a) Obc = Obt = What is the maximum bending stress? 12M h³ (c) Ohr = Oh y || h 9M 7 (b) Obc = Obt (d) pc = Obl = 6M h³ 9M 3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 2 For the assembly shown, determine the stress in each of the two vertical rods if the temperature rises 40°C after the load P=50 KN is applied. Neglect the deformation and the mass of the horizontal bar AB. Compute the vertical movement under the load. Steel Aluminum E=200 GPa E=70 GPa L-4m A=300 mm? a-11.7x10*/°C L-3m A=900 mm a=23x10“ /°C 3 m 3 m 3 m Situation 3
3. The lower ends of the 3 bars in the figure are at the same level before the rigid homogenous 18M block is attached. Each steel bar has an area of 566 mm^2 and E=200GPa. For the bronze bar, the area is 866 mm^2 and E=83GPA. Find the stresses developed in each bar. Steel L=Im Bronze L=1.6 m Steel L=Im 18 Mg
For the truss shown on the figure, determine: Stress at element 4 if u3= 0.175 in and v3=0.5 in A=10in^2 E=30*10^6 moder onfront O O Ⓒ e 20 A Ⓡ O P-1000 > 15 A P-1000 b
Solve the following problems completely and neatly. Use 3 decimal places in all your computations except for strain and rho(5 decimal places). Input your answer in the text box provided in each number. Calculate the stress in the steel of the section in PART B in MPa.0
8. A rigid bar AB is supported by three rods. A load P = 250 kN is applied to the bar. The modulus of elasticity of copper is 110 x 10°6 kN/m^2 and modulus of elasticity of steel is 200 x 10°6 kN/m^2. Steel rod A= 900 sq. mm Steel rod A= 900 2m sq. mm Copper A=1200 sq. mm 2m B 1m 1m Determine the deformation in the rods (in mm). * Your answer
An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1 = 0.8 m; B2 = 1.0 m; B3= 0.6 m. Determine the axial load acting on bar Bị in kN. 35KN B1 B2 B3 ... 10KN 15KN 30KN Determine the axial load acting on bar B2 in kN. Determine the axial load acting on bar B3 in kN. Determine the axial stress of bar B1 in MPa. Determine the axial stress of bar B, in MPa. Determine the axial stress of bar B; in MPa. Determine the total deformation of the bars B1, B2 and B3 in mm. Determine the deformation of the bar B1 in mm. Determine the deformation of the bar B, in mm. Determine the deformation of the bar B3 in mm. 35 (A) 35 в) 20 10 (D 5
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure. Axial loads are applied at the positions indicated. If P = 3000 Ib and the cross sectional area of the rod is 0.5 in^2, determine the stress in each section. Steel Bronze 4P | Aluminum | P 2 ft 3 ft 2.5 ft а. Stress (st) = 19 ksi, Stress (al) = 25 ksi O b. Stress (st) = 16.5 ksi, Stress (al) = 24.2 ksi O c. Stress (st) = 24 ksi, Stress (al) = 18 ksi O d. Stress (st) = 26 ksi, Stress (al) =17 ksi
Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown belowif P = 1639 N, T = 4678 Nm, a = 0.75 m, b = 1.07 m, c = 0.94 m, w = 44 mm, and h = 75 mm . Round off the final answer to one decimal place.
6.59 A square section as shown in the figure below is subjected to bending moment M. (c) Obc = Obl y || h y H What is the maximum bending stress? (a) Obc = obt 12M h³ 9M 2h³ JXC h (b) bc = Obt = (d) %bc =%bt = 6M 4³ 9M h³
An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B, = 0.8 m; B, = 1.0 m; B3= 0.6 m. Determine the axial stress of bar B; in MPa. 35KN B1 B2 ВЗ ... 10KN 15KN 30KN A 218.75 B 125 C 62.5 D 31.25
With FBD please
QUESTION 2 A steel cantilever beam is made of two structural tee- section beams welded together as shown in the Figure 2 below. Determine the allowable safe load (P) that the beam can carry. The allowable stresses are: 0-150MPa in tension and compression, T=100MPa in shear, and q=2000N/mm on the welded joint. 150 -200mm- -150- 25 weld 25 ΝΑ 25 M=P V=P -1.0m- Figure 2 weld 0.5m 31