Two vertical forces are applied to a beam of the cross-section shown. Determine the maximum compressive stress in the portion BC of the beam (P=140 kN; a=7.5 m; b=4.2 m; y=119.44 mm from the bottom). Note that y, is the centroid of the cross-section.PO a 583.4 MPaO b. 741.7 MPaOc 596.8 MPaO d. 587.8 MPaOe. 781.8 MPaPD25 m

Given Data: a = 7.5 m b = 4.2 m

Two vertical forces are applied to a beam of the cross-section shown. Determine the maximum compressive stress in the portion BC of the beam (P= 140 kN; a=7.5 m; b-4.2 m; ye-119.44 mm from the bottom). Note that y, is the centroid of the cross-section. O a. 583.4 MPa O b. 741.7 MPa OC 596.8 MPa O d. 587.8 MPa O e. 781.8 MPa D 200 mm 25 mm + 100 mm 150 man

Two vertical forces are applied to a beam of the cross-section shown. Determine the maximum compressive stress in the portion BC of the beam (P= 140 kN; a=7.5 m; b-4.2 m; ye-119.44 mm from the bottom). Note that y, is the centroid of the cross-section. O a. 583.4 MPa O b. 741.7 MPa OC 596.8 MPa O d. 587.8 MPa O e. 781.8 MPa D 200 mm 25 mm + 100 mm 150 man

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The bent steel bar shown in Fig. P-906 is 200 mm square. = 4.2 MPa = 29.2 MPa; og 906. Determine the normal stresses at A and B. Ans. .211 A 250 mm- جاش A 200 mm 450 mm Figure P-906. 100 mm 500 kN 3
Determine the maximum compressive bending stresses in the beam shown. Let P = 16
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If 0 = 68 MPa, determine the principal stresses acting at the point. 114 MPa 66 MPa 157.9 MPa and -155.4 MPa 82.0 MPa and -83.7 MPa O 121.2 MPa and -138.0 MPa O 167.4 MPa and -98.1 MPa O 133.2 MPa and -131.2 MPa
9
2. Determine the internal forces and draw the diagrams
SHOW SOLUTION AND ILLUSTRATION
Pls show complete solution and fbd
The cross-sectional dimensions of the beam shown in the figure are a = 4.1 in., b= 5.1 in., d= 4.3 in., andt= 0.33in. The internal bending mornent about thez centroidal axis is M, = -4.15 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam. b y |(ур.) |d a Answers: (a) OmaxT psi (b) Omax C= psi
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torqueT that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. 75 mm 50 mm A Bronze B Steel
Steel plate (2) b. 4. Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. a. 8.5 ksi 5.7 ksi 10.5 ksi Draw Mohr's circle for this state of stress. Me grapting page is ba b. Determine the principal stresses and the maximum in-plane shear stress acting at the point. Ans. c. Show these stresses on an appropriate sketch. <
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F1 = 16 kips, F2 = 30 kips, and the normal stress in each rod must be limited to 18 ksi, determine the minimum diameter d1 required for rod (1).
X= 460 lb. Find the stress at points A and B. Determine the point where the neutral axis intersects like ABD. The neutral axis intersects AB at (blank) inches from A and intersects BD at (blank) inches from D.