Two vertical forces, each of magnitude P= 13 kN, are applied to a beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam. 10 mm 10 mm - 50 mm 50 mm 10 mm B 150 mm P 250 mm C 150 mm D

Q: SITUATION 21 A rectangular steel block is 300 mm in the x direction, 200 mm in the y direction, and…

A:

Q: An 8 m simple beam is loaded with a 228 kN point load at the first third of its length. The cross…

A:

Q: Differentiate the normal stress, shear stress and bearing stress.

A: Reference : Basic Mechanics, Types of stresses. To differentiate between : 1. Normal stress 2. Shear…

Q: 4) Explain and illustrate variations of normal stresses everywhere on the bar and state why it is…

A: Given: A bar carrying tensile load and having two holes on the bar. Tensile load=P Due to this load,…

Q: Describe about the deviator stress.

A: - Deviator stress is also know as Principal stress difference, Shear stress, Back pressure stage -…

Q: Which stress element below correctly shows the normal and stress at point X? M T A G B D H Write the…

A:

Q: Find the modulus of elasticity Stress=2 MPa Strain=0.1

A: Given data : Strain is denoted by ε Stress is denoted by σ   To find : Modulus of elasticity

Q: 5. A metallic top-hat stringer reinforced wing skin (function of the material A=150) has a width of…

A: The function of the material = 150Width =1.5 mUnsupported length =0.5 mApplied compressive load =120…

Q: 2. Shear stress is caused due to a) Friction b) Temperature c) Pressure d) Volume

A: Shear stress, force tending to cause deformation of a material by slippage along a plane or planes…

Q: How are the normal stresses distributed in the cross section in case of pure tension? (a) unevenly…

A: It is requir d to answer about the distribution of normal stress in case of pure tension.

Q: The state of stress at a point Q is Ox = 100 MPa, o, = 20 MPa, oz = -40 MPa, Txy = 0 MPa, Tyz = 40…

A:

Q: Explain Unsymmetrical bending and a method to find the stress in an Unsymmetrical section.

A: Unsymmetrical bending takes place in beams. If the moment diagram is unsymmetrical in nature then…

Q: Discuss Computation of Effective Stresses

A: Basic concepts- Effective Stress- Effective stress is a parameter in soil that is responsible for…

Q: (c) In your own words, explain the engineering importance of solving for principal stresses and max…

A: Brief concept introduction- Principal Stresses- These are the normal stresses that act on the…

Q: Figure 2 shows the stress at point A of I-section beam. status given. a) Calculate the principal…

A: Given data- σx=40 MPaσy=-20 MPaτxy=30 MPa

Q: Find the modulus of elasticity Stress=2 MPa

A: According to given data  Stress = 2 MPaStrain = 0.1

Q: According to Saint-Venant’s principle, the actual stress distribution at the support is highly…

A: Saint Venant's Principle:

Q: A cast iron link is 50mm wide by 250mm high by 550 mm long. The allowable stress in tension is 50…

A:

Q: 11.18 A long, flat steel bar 4 in. wide and 3 in. thick is reduced in width to 3 in. There are…

A: Applied load (P)=12000lb D=4in d=3 in Thickness (t)=3/8 in

Q: Describe the concept for analysis of stress at a point where external loading causes different…

A: Stress Definition and Analysis – The body offers resistance to the external loading against the…

Q: Is the minimum principle stress is always negative?

A: To determine: Whether minimum principal stress is always negative.

Q: The cross-section of a pretensioned prestressed concrete beam is shown in figure. The reinforcement…

A:

Q: Consider a case where a place where a plate is subjected to combined loading, including pressure q…

A:

Q: What would be the temperature at which the bar will have a compressive stress of 3 MPa given that at…

A: Elongation due to temperature change δT=Lα(ΔT)ΔT=T2-T1=T2-(-20)=T2+20

Q: The stress between a brick and another one below in a wall is bearing .stress True False

A: The stress between a brick and another one in a below is bearing stress, The load is transferred…

Q: Define and Discuss the following different type of insitu stresses.         Total stresses Insitu…

A: 1- TOTAL STRESS :  - In case of load application on soil, the water in the pores as well as the…

Q: Determine the strain-stress relations of an isotropic material for a cylindrical coordinate system.

A:

Q: Determine principal  stress

A:

Q: Describe the Basic step in determining stresses on a random plane through a point in terms of known…

A: if σ1 and σ2 are known principal stress as shown in figure, then normal stress and shear stress on…

Q: Question #4 For the cantilever beam shown in Figure 4, a) Determine the maximum shear stress on the…

A: Given data  Point load  Length  Cantilever beam  Cross section  Web thickness  Flange thickness

Q: Two steel plates each of width 150mm and thickness 10mm are connected with three 20mm diameter…

A:

Q: Which of the following does not cause any changes in the value of bending stress on a beam?

A: Which of the following does not change any value in bending stress in beam- (D)- Load acting on the…

Q: Is this a frame or a truss? Calculate the cross section of the bar BC if the allowable normal stress…

A: Normal stress= 165 MPa To determine- a) Is this a frame or a truss?                         b)…

Members with compression and bending

Compression members are structural elements that carry compressive axial force. They are the vertical members of a building that support beams and their design, which is governed by buckling and strength. Columns are known as struct or compression members, which are subjected to compressive forces. These members provide stiffness to the building and avoid any imperfection regarding the transfer of axial load. For instance, webs in a truss, braces in a framed structure, tiers, and so on.