The beam shown below is suspended from two steel rods as shown and is initially horizontal. The midpoint B of the beam is deflected 15 mm downward by force Q. The steel used for the rods has properties E = 200 GPa and  = 275 MPa, determine a. the required maximum value of Q. b. the deformation of rod AD. c. the deformation of rod CE.

The beam shown below is suspended from two steel rods as shown and is initially horizontal. The midpoint B of the beam is deflected 15 mm downward by force Q. The steel used for the rods has properties E = 200 GPa and  = 275 MPa, determine a. the required maximum value of Q. b. the deformation of rod AD. c. the deformation of rod CE.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are mm while those at CD decrease 70 x 10 mm in the 260- -3 found to increase 30 x 10 -3 mm-gage length. Using E = 150 GPa, determine the flexural stress at the bottom fiber. 40mm, b Answer must be in MPa. Given: a = = 110 mm, andc= 80 mm. gage length a mm b b mm c mm 8.
3. The rigid bar ABC is pinned at B and attached to the two vertical rods. Initially, the bar is horizontal and the vertical rods are stress-free. Determine the stress in the steel rod if the temperature of the both rods is decreased by 30°C. Neglect the weight of bar ABC. Steel L=0.9 m A 300 mm E= 200 x 10 N/m' a= 11.7 um/(m C) Aluminum L=1.2 m A = 1200 mm E = 70 x 10 N/m a= 23 pum/(m "C) Answer: Ost B 0.6 m 1.2 m
At a temperature of 34°F, a 0.06 in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [a = 12.5 x 10-6/°F] and bar (2) is stainless steel [a = 7.3 x 10-6/°F]. The supports at A and C are rigid. Determine the lowest temperature at which the two bars contact each other. (1) 33m B (2) Answer: Final temperature = 55 in. -0.06. gap °F.
The following composite shaft is loaded as shown in the figure. The AC segment of the shaft is solid; it is connected to the hollow shaft CD with the help of a rigid flange at C. A torque of 100 Nm is applied at B, as shown. A uniformly distributed torque of 200 Nm/m is applied over the entire length of CD (2m), also shown in the figure. Please ignore the thickness of the rigid flange at C. Given: GAC = 140 GPa, diameter of AC = 20 mm. GCD = 200 GPa, inner diameter of AC = 40 mm, outer diameter of AC = 50 mm. a. Determine the absolute maximum shear stress on the shaft. Specify where it occurs along the length of the shaft and on the circumference of the shaft. Draw the state of stress on a volume element corresponding to the maximum absolute shear stress location. Show proper perspective when drawing the state of stress. b. Determine the absolute maximum shear strain on the shaft. Specify where it occurs along the length of the shaft and on the circumference of the shaft. Be careful…
The solid shaft, made of three different materials, carries the two torques shown. (a) Calculate the maximum shear stress in each material. (b) Find the angle of rotation of the free end of the shaft. The shear moduli are 28 GPa for the aluminum, 83 GPa for steel and 35 GPa for bronze. Aluminum 100 mm -3 m- 4 kN.m Steel 75 mm -2 m 1.5 kN - m Bronze |--15m-l
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 30 x 10-3 mm while those at CD decrease 70 x 10 mm in the 270- -3 mm-gage length. Using E 180 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa. Given: a 50 mm, b = 120 mm, and c = 70 mm. gage length A a mm B b mm D. C. c mm
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 20 x 103 mm while those at CD decrease 60 x 103 mm in the 230- mm-gage length. Using E = 180 GPa, determine the flexural stress at the top fiber. Answer must be in MPa. Given: a = 40 mm, b = 130 mm, and c= 70 mm. gage length a mm A B. b mm c mm
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.21 in.? and an elastic modulus of 2350 ksi. Bar (2) has a cross-sectional area of 1.032 in.? and an elastic modulus of 4100 ksi. Assume L1=20 in., L2=49 in., Q=7.1 kips, P=2.9 kips, and R=12.9 kips. Determine the horizontal deflection of end C relative to end A. P (1) (2) C В L1 L2 Answer: uc/A in. %3D