The aluminum bar ACDB is rigidly connected to a steel tube in CD. The data is presented in the table. If the load P is equal to 125 kN, determine:The stress of aluminum in segment AC. Answ: 63.66 MPaThe stress of aluminum in segment CD. Answ: 13.93 MPaThe stress in steel in segment CD. Answ: 39.79 MPaThe total deformation of the bar. Answ: 0.29273 mm d₁BPL Bar (1) AluminumBar (2) SteelDistance cDistance bElastic modulus, E70 GPa200 GPaDiameter, Dd₁= 50 mmd2= 75 mm100 mm150 mm

Detailed step by step solution is given below, still if you have any query please feel free to…

Answered: d₁ B P L Bar (1) Aluminum Bar (2) Steel…

d₁ B P L Bar (1) Aluminum Bar (2) Steel Distance c Distance b Elastic modulus, E 70 GPa 200 GPa Diameter, D d₁ = 50 mm d2 = 75 mm 100 mm 150 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The details of the principal stresses at a certain point in a steel member are as follows: Major…

A: Given - Major principal stress, σ1 = 180 N/mm2 (Tensile) Yields stress, σy = 240 N/mm2 To find -…

Q: Punch Aluminum =4 mm d-20 mm

A: Given that t=4 mmd= 20 mmUltimate shear stress = 280 Mpa

Q: The assembly consists of a rigid bar AB, pinned at 0, that is attached to the steel and aluminum…

Q: The bar 1 consists of an aluminum cover and a brass core. The data is presented in the table.…

A: Please refer explanationExplanation:Step 1: Step 2: Step 3: Step 4:

Q: A 16 mm steel bar AB and a 25 mm steel bar BC support a load P = 7,500 N as shown. If E = 200 GPa,…

A: Given data: Diameter of AB steel bar=16 mm Diameter of BC steel bar=25 mm Load=7500 N It is asked…

Q: The aluminum rod AD (E=73 GPa, a=23×10-6/ºC) has a diameter of 15 mm and is attached to the rigid…

A: Determine: a) The location and magnitude of the maximum stress acting on the rod AD b) Displacement…

Q: In the figure shown, determine the normal stresses at AD • and BC • shearing stress at bolt D • ,…

A: Calculation: The moment at point C can be calculated as, ∑MC=0200.25+0.4-RD0.4=013-RD0.4=0RD=32.5 kN…

Q: A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as…

A: The given data is as follows: E=200 GPaAllowable stress in rod CD=124 MPa

Q: A 2-m long steel rod, 10-mm in diameter, is carrying a load of 20 kN. (a) what is the axial stress…

A: This question is related to the Strength of material. In this question we calculate axial stress and…

Q: I Hinge it 大 2L 3.

Q: bar shown if the temperature increas supports are unyielding and that the buckling. 4 Aluminum A =…

Q: Explam how the total stess at a distance z be determined from the figure below Com ground surface…

A: For multi layered soil Total stress is given by :σt=∑ γtγ=unit weightst=thickness of each layer

Q: PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the…

A: Given E= 70Gpa= 70000Mpa

Q: PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the…

Q: calculate the strength reduction factor at the minimum strain of extreme tension steel f'c=28 mpa…

A: Given data: f'c=28 mpa fy=420 mpa

Q: Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the…

Q: 25 KN III a a ASTEEL ACOPPER STEEL 2.8 m 3.6 m hree vertical rods of equal distance, each has a…

A: Data given:Length of 2 steel rods = 3.6mLength of copper rod = 2.8mDiameter =…

Q: After load Pis applied to the pin-connected structure shown, a normal strain of ɛ= + 770 uɛ is…

A: Given data Normal strain = 770 × 10 -6 in /in E= 29000 ksi Yield strength = 42 ksi

Q: 3. An aluminum bar having a cross-sectional area of 0.25 sq. in. carries the axial loads applied at…

Q: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure P-108.…

A: Given data in question Area Stresses Loads To find out Maximum value of P so that stresses should…

Q: 160KN 个 160KN 6cm 6cm 40 cm

Q: A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall…

A: Given:- 5.0 m simple beamPu=45kNwu=44.24kN/mspan=5.0mTo find:-stress in steel

Q: -A:. An aluminum rod is rigidly attached between a steel rod and a bronze rod as n in the Fig. Axial…

A: For bronze: σbrAbr=2P100200=2PP=10,000 N

Q: Q. A For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138,…

A: Note:- as per our company guidelines we are supposed to answer only first part. Kindly repost other…

Q: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown. Axial loads are…

A: Maximum stress The terms "maximum stress" and "minimum stress" both refer to the maximum tensile…

Q: An aluminum bar carries the axial loads at the positions shown. If E=70GPA, cumpute the total…

Q: Q2 - The assembly shown below consists of three rods AB, CD and EF with the following properties: AB…

Q: AN ALUMINUM ROD IS RIGIDLY ATTACHED BETWEEN A STEEL ROD AND A BRONZE ROD AS SHOWN IN THE FIGURE.…

Q: Q3: For the assembly shown in Fig. Q3. Axial loads are applied at the positions indicated. Find the…

Q: 2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions…

Q: AN ALUMINUM TUBE IS FASTENED BETWEEN A STEEL ROD AND BRONZE ROD AS SHOWN IN THE FIGURE. AXIAL LOADS…

Q: SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and…

Q: Bronze A = 300mm? 2.00 m E = 83 GPa Steel 1.00 m A = 600mm? E = 200 GPa A В 0.60m 1.00 m 1.00m MN kN

Q: The maximum and minimum normal stresses is known as?

A: The combination of normal and shearing stresses acting on two mutually perpendicular planes is…

Q: 1. The assembly has the diameters and material makeup indicated. If it fits securely between its…

A: αal=12.8×10-6/°Fαbr=9.6×10-6/°Fαst=9.6×10-6/°FEal=10.6×106 lb/inEbr=15×106 lb/inEst=128×106 lb/in

Question

The aluminum bar ACDB is rigidly connected to a steel tube in CD. The data is presented in the table. If the load P is equal to 125 kN, determine:

The stress of aluminum in segment AC. Answ: 63.66 MPa
The stress of aluminum in segment CD. Answ: 13.93 MPa
The stress in steel in segment CD. Answ: 39.79 MPa
The total deformation of the bar. Answ: 0.29273 mm

Bar (1) Aluminum
Bar (2) Steel
Distance c
Distance b
Elastic modulus, E
70 GPa
200 GPa
Diameter, D
d₁
= 50 mm
d2
= 75 mm
100 mm
150 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step by step

Solved in 1 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

In the figure shown, the AB part of the rod is made from brass while the BC part is fabricated from aluminium, both parts are restrained at the ends. Find: 1) The normal stresses oAB and OBC + when the temperature is increased to 42°C. 2) The deflection at point B (SB) Brass: ab=20.9*10-6 1/°C, Eb=105GPA Aluminum: aal=23.9*10-6 1/°C, Eal=72GPA 60 mm diameter A 1.1 m B 40 mm diameter 1.3 m C Aluminum Brass
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown below. Axial loads are applied at the positions indicated. Find the maximum value of P in Newton that will not exceed a stress in steel of 150 MPa, in aluminum of 87 MPa, or in bronze of 97 MPa.
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress (in Mpa) in the bronze given that P= 188 kN? Express your answer in four decimal places.
3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 13.05 ksi, or in bronze of 100 MPа. Aluminum A = 400 mm? Bronze A = 200 mm Steel A = 500 mm? 2P 4D 2.5 m 2.0 m 1.5 m
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
pls help me. thank u refer to the picture attached below.
Solve please
5. The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that the rods were initially stress-free, what is the largest load P that can be applied without exceeding stresses of 150 MPa in the steel rod and 70 MPa in the bronze rod? -2 m- -1.5 m- 1.5 m- Bronze A = 300 mm2 E = 83 GPa L=2 m Steel A = 900 mm2 E = 200 GPa L = 1.5 m