Question 3 [10] 3.1. (i) Describe the differences between a linear ToF mass spectrometer and an orthogonal ToF instrument. (ii) What are the advantages and limitations of these two geometries? (2) (3) (3) 3.2. Describe three ways of introducing a sample into an ICP torch. 3.3. A chromatogram of a mixture of compound X and Y provided the following data (see Table 3.1): Table 3.1: Chromatographic data for U and V 3 Retention time (min) Peak width (at base) Mobile phase peak 0.81 0.01 Compound X 9.35 Compound Y 10.76 1.13 1.19 (i) For compound X, calculate (correct to 3 sig figs) its retention factor. (1) (ii) Calculate (correct to 3 sig figs) the selectivity factor for compound X and Y. (1)

Question 3 [10] 3.1. (i) Describe the differences between a linear ToF mass spectrometer and an orthogonal ToF instrument. (ii) What are the advantages and limitations of these two geometries? (2) (3) (3) 3.2. Describe three ways of introducing a sample into an ICP torch. 3.3. A chromatogram of a mixture of compound X and Y provided the following data (see Table 3.1): Table 3.1: Chromatographic data for U and V 3 Retention time (min) Peak width (at base) Mobile phase peak 0.81 0.01 Compound X 9.35 Compound Y 10.76 1.13 1.19 (i) For compound X, calculate (correct to 3 sig figs) its retention factor. (1) (ii) Calculate (correct to 3 sig figs) the selectivity factor for compound X and Y. (1)

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter11: Atomic Mass Spectrometry

Section: Chapter Questions

Problem 11.8QAP

See similar textbooks

Similar questions

Mass spectrometry is an extremely versatile detection system for GC. However, interfacing an HPLC system to a mass spectrometer is a much more difficult task. Describe the major reasons why it is more difficult to combine HPLC with mass spectrometry than it is to combine GC with mass spectrometry.
Please correct answer and don't use hend raiting
When would you use flame ionisation detectors in chromatographic analysis? (a) analysis of hydrocarbons at trace levels (b) Analysis of organic and inorganic compounds at normal concentration levels (c) Analysis of samples that you want to preserve (d) Analysis of hydrocarbons at trace levels and analysis of samples that do not need to be preserved (e) None of the other answers Pick one and why...
3 questions...
A gas chromatogram of a mixture of toluene and ethyl (a) Measure w1/2 for each peak to the nearest 0.1 mm. When the thickness of the pen trace is significant relative to the length being measured, it is important to take the pen width into account. It is best to measure from the edge of one trace to the corresponding edge of the other trace, as shown at the bottom of the left column. (b) Find the number of theoretical plates and the plate height for each peak.
1) Study the chromatograph (below) of a mixture of Compounds A and B, run on the GCs in the teaching labs at CU Boulder. Compound A has the shorter retention time. STAAT 61 1.11 227 RT TYPE AREA XXXX XXXX XXXX AREAS 0.009 55874 44.117 ARIHT 0.61 XX XX XX 1.11 2.27 XX XX XX TOTAL AREA=XX MUL FACTOR=XX 1. What is the retention time of compound A? Compound B? 2. Which compound is present in a larger amount? 3. Which compound has the lower boiling point? 4. What would happen to the retention times of compounds A and B if the column temperature were raised? 5. You suspect that compound B is octane. What can you do to provide supporting evidence for this hypothesis?
In a chromatographic separation of two components A and B. Component A has a higher Rf value than component B. This implies that: A. Component B has a higher affinity than A for the mobile phaseB. component B elutes first in the columnC. A has a higher affinity than B for the mobile phaseD. Component A has a higher affinity than B for the stationary phase.
1,3,5 what the correct answer?
Kk.312.
Don't use AI.
Directions: (1) Determine the total volume of the standards by using a formula in the appropriate boxes (your instructor will help you with this). (2) Determine the concentration of Cu2+ in each standard, also using a formula in the appropriate cells. (3) Plot the absorbance as a function of Cu2+ concentration. Determine the equation for the best-fit line. 1.0 M ethylenediamine (mL) concentration Cu2+ absorbance (AU) at 550 nm 0.01 M CuSO4 5H2O H2O total volume stock Cu2+ standard (mL) (mL) (mL) (units) concentration (M) 1 0.50 0.00 9.50 0.025 0.01 2 0.50 0.50 9.00 0.031 0.01 3 0.50 1.00 8.50 0.048 0.01 4 0.50 2.00 7.50 0.153 0.01 5 0.50 3.00 6.50 0.223 0.01 0.50 4.00 5.50 0.307 0.01 7 0.50 5.00 4.50 0.384 0.01
[1] In paper chromatography, why do some ions move only a short distance from the point of application while others move much more?