Q4: A circular bar ABC, 4 m long, is rigidly fixed at its ends A and C. The portion AB is2.2 m long and of 50 mm diameter and BC is 1.8 m long and of 25 mm diameter. If atwisting moment (torque) of 650 N.m is applied at B. determine (a) the values of theresisting moments at A and C; (b) the maximum shear stress in each section of the shaft;(c) the angle of twist of each portion. The modulus of rigidity for the material of theshaft; G 80 GN/m².

Q4: A circular bar ABC, 4 m long, is rigidly fixed at its ends A and C. The portion A 2.2 m long and of 50 mm diameter and BC is 1.8 m long and of 25 mm diameter. twisting moment (torque) of 650 N.m is applied at B. determine (a) the values of resisting moments at A and C; (b) the maximum shear stress in each section of the sh (c) the angle of twist of each portion. The modulus of rigidity for the material of shaft; G = 80 GN/m².

Q4: A circular bar ABC, 4 m long, is rigidly fixed at its ends A and C. The portion A 2.2 m long and of 50 mm diameter and BC is 1.8 m long and of 25 mm diameter. twisting moment (torque) of 650 N.m is applied at B. determine (a) the values of resisting moments at A and C; (b) the maximum shear stress in each section of the sh (c) the angle of twist of each portion. The modulus of rigidity for the material of shaft; G = 80 GN/m².

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T = 50 lb.ft is applied to it at C, determine the rotation angle that occurs at C relative to A and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst = 11500 ksi, Gbr = 5600 Ksi. 3 ft 2 ft 0.5 in. B 1 in. T = 50 lb·ft
3. The center post B of the assembly has an original length of 124.8 mm whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross sectional area of 400 mm². Ea=70 GPa. Use the Force Method 100 mm -100 mm 800 kN/m 125 mm 800 kN/m
The bridge is pinned at A and has a roller at G. A downward load of 12.5 lb is applied at point C, and a downward load of 25 lb is applied at E. The support reactions at the pin and roller are shown on the image. Find the stress in members making up the bridge using either the method of joints or method of sections.
2. All members of the truss A B C shown have a cross- sectional area of 500 mm? and all pins have a diameter of 20mm. Determine: 2 m (a) The axial stresses in members BC and DE F E D -2 m 2 m 2 m- (b) The shear stresses in the pin at A, assuming the pin is in double shear P = 21 kN
1. We have a truss structure with a hinge on the left and a roller on the right. (Use method of moments ONLY for finding the members and use the numbered name only for each member) 30.00" a) Find the force acting on members 2, 3, 7, 9, 14, 15. (Indicate Compression or Tension) b) Determine the normal stress @ members 2, 3, 7, 9. (Use figure 2 for cross-sectional area) P/2 30.00" T IP 30.00" T Figure 1 30.00" P/2 30.00" P/2 10.00" 20.00" 2.00" 0.20" Figure 2 0.20" 2.00" 0.20"!
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 7 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 7 mm in diameter. Assume a = 640 mm, b = 320 mm, h = 400 mm, and 8= 55°. If the normal stress in tie rod (1) cannot exceed 200 MPa and the shear stress in pin B cannot exceed 100 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) a B KN h
3. The center post B of the assembly has an original length of 124.8 mm whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross sectional area of 400 mm². Ea=70 GPa. Use the Force Method 100 mm -100 mm 800 kN/m 125 mm 800 kN/m
3. Determine the required diameter of the pins at A and B to the nearest 1mm if the allowable shear stress for the material is T= 300 MPa. Pin A is subjected to doble shear, whereas pin B is subjected to single shear. A 1.5 m B 1.5 m C D 30 kN 2.25m
The joint between a diagonal and a chord in a timber truss is shown. The compressive force P in the diagonal is 20 kN. Determine the compressive stress in the diagonal, the bearing stress on plane ab, and the shear stress on plane ac. Both the chord and the diagonal are 150 mm by 150 mm (full nominal size) in cross-section. 40 mm Diagonal Chord a 160 mm
The bell-crank mechanism is in equilibrium for an applied load of P = 34 kN. Assume that a = 240 mm, b = 140 mm, and 0 = 63°. The pin at B has a diameter of d = 15 mm, and the bell crank has a thickness of t = 6 mm. Calculate the bearing stress in the bell crank at pin B. F₁ Bell crank B a Support bracket Part 1 Use equilibrium to determine the magnitude of the reaction force at pin B. Answer: B = i kN
The cross-section of the two wooden members is a rectangle with a = 120 mm and b 60. They are joined by a simple glued joint as shown. Knowing that P = 9 kN, determine the normal and shear stresses at the joint when (a) a = 30°, (b) a = 45°.