= The solid steel shaft carries the torques T₁ 750 N-m and T₂-1200 N-m. Using L₁ L₂ 2.5 m and G-83 GPa, determine the smallest allowable diameter of the shaft if the shear stress is limited to 60 MPa and the angle of rotation of the free end is not to exceed 40. (Hint: Analyze for 0 governs and T governs). Odmin = 54.1 mm Odmin - 46.7 mm Odmin= 51.9 mm Odmin 26.0 mm T₁ B 12 с 1₂

= The solid steel shaft carries the torques T₁ 750 N-m and T₂-1200 N-m. Using L₁ L₂ 2.5 m and G-83 GPa, determine the smallest allowable diameter of the shaft if the shear stress is limited to 60 MPa and the angle of rotation of the free end is not to exceed 40. (Hint: Analyze for 0 governs and T governs). Odmin = 54.1 mm Odmin - 46.7 mm Odmin= 51.9 mm Odmin 26.0 mm T₁ B 12 с 1₂

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T 50 lb.ft is applied to it at C, determine the rotation angle that occurs at C relative to A and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst = 11500 ksi, Gbr 5600 Ksi. %3D %3D 3 ft 2 ft 0.5 in. 1 in. T = 50 lb ft
Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 15 mm. Determine the largest allowable value of P if the shear stress in the shaft is not to exceed 120 MPa and its angle of twist is limited to 5°. Use G = 80 GPa for steel. (Note: Two values of P are to be compared here). 300 mm P. B 500 mm A
Prob 1. The rigid bar below is supported by a pin and two rods and must support a load of 100 kN is placed 3 m from A. The brass (Ebrass = 85 GPa) rod has a cross section of 30 x 30 mm and the copper (Ecopper = 120 GPa) rod 20 x 20 mm. Determine the normal stress and deflection of both bars. 1.5 m 2 m B -copper 100 kN brass- 3m 3 m E
The aluminum rod AB (G = 27 GPa) is bonded to the brass rod BD (G = 39 GPa). Knowing that portion CD of the brass rod is hollow and has an inner diameter of 40 mm, determine the angle of twist at A. 60 mm TB = 1600 N-m 36 mm TA = 800 N·m A 400 mm B 375 mm --- 250 mm Then, determine the maximum and minimum shearing stress in shaft CD.
Two aluminum (Ea=77 GPa) rods AB and CD, and a steel (Es=202 GPa) rod EF support a 82.7 kN load P. Each of the rods has a 400 mm2 cross- sectional area. Neglecting the deformation of rod BED, determine the change in length (in mm correctly up to two decimal places) of rod AB. A C P 500 mm В E 400 mm F
The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T = 50 lb.ft is applied to it at C, determine the rotation angle that occurs at C relative to A and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst = 11500 ksi, Gbr 5600 Ksi. %3D 3 ft 2 ft 0.5 in. 1 in. T 50 Ib-ft
The 20-mm diameter shaft is subjected to torques as shown. The shaft is made of steel with the following properties: elastic modulus, E=200 GPa and Shear Modulus, G=75 GPa, Tb-80Nm Determine the following: a. Absolute the maximum torsional shear stress b. Angle of twist of the end B with respect to the support Show complete solution with fbd A 30 N-m 200 mm B 80 N-m 20 N-m 800 mm 600 mm
A flat steel bar, 25mm wide by 6mm thick and 1 m long, is bent by couple applied at the ends so that the midpoint deflection is 20mm. Use E=200 GN/m^2. Compute: a. the maximum stress in the bar (MPa) b. the magnitude of the couples(N-mm) Round to the nearest whole number.
2max 1 max A beam comprises of two metals (1 and 2). Both the metals are in contact as shown in figure. If a moment M, is applied, what is the value of 0₁/0... It is given that both the metals will bend separately about their own neutral axis. Also draw bending strain and bending stress diagram. Mo Mo at th Jicc E₁, I, E2, 12 d₁ d₂
7.A cast-iron machine part is acted upon by the 3kN.m couple shown. Knowing that E=165GPA and neglecting the effect of fillets. i) Determine the maximum tensile and compressive stress in the casting ii) Determine the radius of curvature of the casting. 90 mm 20 mm 40 mm 30 mm M = 3 kN m
3. The shaft consisting of steel and aluminum segments carries the torques T and 2T. Find the largest allowable value of T if the working shear stresses are 12500 psi for steel and 7800 psi for aluminum and the angle of rotation at the free end must not exceed 6 degrees. Use G = 12 x 10° psi for steel and G = 4 x 10º psi for aluminum. T Aluminum 2 ft 1.6 in dia. 2T Steel 2 in dia. 3.2 ft
A solid circular bronze [G = 6,500 ksi] shaft, 6.0 ft long and 1.325 in. in diameter, carries a torque of 90 Ib-ft. For this shaft, determine: (a) the maximum shear stress in the shaft. (b) the magnitude of the angle of twist. Answer: (a) Tmax = psi (b) Ф%3D