Q 2:- For the network shown in Fig. 2: a) Find the total impedance 7r. h) calculate the current Ic) determine the voltage V, using voltage divider rule, d) Find the average power delivered to thenerwork. e) Find the power factor of the network. E= 100 V 20 X, = X, = 200n100nR100nE5600

Answered: Image /qna-images/answer/e944ca43-6987-4b5a-9bb3-599c00bfb76b.jpg

Answered: Q2- For the nerwork shown in Fig. 2: a)…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3. Perform the following steps for the given circuit in below.c) Find the Av, if the Vs = 100mV_rms, IDSS = 12mA, VP = -4V, VDD = +12V, RD =3.6kΩ, RS = 1.1kΩ.d) Find the Vo, if a load resistance of 10kΩ is connected to the output of the circuit.Vs = 50mV_peak, IDSS = 12mA, VP = -4V, VDD = +12V, RD = 3.6kΩ, RS = 1.1kΩ.
A single-phase consumer who lives in San Francisco has an annual average monthly consumption of 430 kWh. In San Francisco, the average hours of full sun is 3.96 hours / day. Considering the losses of 20%, based on the data below (image), find: The number of photovoltaic panels that will be used.
Problem : In the case of an industrial load with a power factor of 0.707 lagging, consuming 100 kW, and the line voltage at 60 Hz is 480Vrms, with a line resistance of 0.1Ω between the power company's transformer and the load, calculate the amount of power saved if the load's power factor changes to 0.94 leading. The answer is "3.771 Kilo-Watt has been saved" and also I want to know the concept of 'Power Factor'.
20. A circuit is composed of a resistance of 22 ohms, an inductance of 0.11 henry and a capacitance of 12 microfarad, all connected in parallel to a 115-volt 60-Hz supply. Calculate the impedance of the circuit 18.61 ohms 33.78 ohms 12.54 ohms 20.20 ohms
calculations as one file in the Midterm exam answrers submission link. In a industry, a balanced 3 phase star connected load draws power from a 430 V supply. Two wattmeter's indicate 8000 W and 3000 W respectively, when connected to measure the input power of the load, the reverse switch being operated on the meter indicating the 3000 W reading. Determine, The Input power, P = The power factor, coso = The line current, IL =
Question 5.K-Map is used for A. Logic Minimization B. Expression Maximization C. Summing of Party bits D. Logic gate creation
QUESTION 1 For the network of Fig. Q1, a) Using exact approach, determine Ig. Ig and re. b) Sketch the AC equivalent circuit c) Calculate Zi and Zo. d) Find Av. Vcc = 18 V B = 100 ro = 100k 2 Rc = 2.2kn R, = 68kn Vo C. +V, oHH C, R = 1.2kn R = 22kn RE = 6802 | z. Z, FIGURE Q1 ww
For the circuit shown in the image: What is the value of Sa, Se, Sc, Sp and STotal (give answer in a complex number in rectangular form) • What is the power factor of the circuit. (give answer in a real number) • What is the value of the impedance that the source sees (give answer in a complex number in rectangular format). B) 200 KVAR fp= 0,80 leading A) 115 kW C) 180 kVA D) 180 KVAR 120230° (+ fp= 0,60 lagging fp= 0,50 lagging fp= 0,70 leading
7. A 3-ph, 3-wire balanced load with a lagging power factor is supplied at 400 V between lines. A single-phase wattmeter when connected with its current coil in the A-line and potential coil between A and B lines gives a reading of 6 kW. When the same terminal of the voltage coil are switched over to B- and C- lines, the current coil connections remaining the same, the reading of the wattmeter remains unchanged. Calculate the line current and the pf of the load.
In the circuit below find a) Find the total admittance, Y b) Find the power factor of the network. c) Calculate the voltage V, and the current I,. d) Find the average power delivered to L2and the total average power delivered to the network. R,=20, R2=R3=8N, L,=9.56 mH, L,=4.78 mH, C=398 µF + V2 R2 R ll ll i-V2 (5) sin 2n100t
. A power station has a connected load of 48 MW. The energy generated for the year is 61,500 MWh. If the station has a load factor of 35%, solve the demand factor of the station. Answer: 0.4179 or 41.79% Subject: Distribution System and Substation Design
2

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

Q2- For the nerwork shown in Fig. 2: a) Find the total impedance 7. b) calculate the current I c) determine the voltage V, using voltage divider rule, d) Find the average power delivered to the network. e) Find the power factor of the network. E = 100 V 20' X, = X1, = 2009 Xe 100n R 100n X, X, 5600