. A 3-ph, 3-wire balanced load with a lagging power factor is supplied at 400 V between lines. A single-phase wattmeter when connected with its current coil in the A-line and potential coil between A and B lines gives a reading of 6 kW. When the same terminal of the voltage coil are switched over to B- and C- lines, the current coil connections remaining the same, the reading of the wattmeter remains unchanged. Calculate the line current and the pf of the load.

. A 3-ph, 3-wire balanced load with a lagging power factor is supplied at 400 V between lines. A single-phase wattmeter when connected with its current coil in the A-line and potential coil between A and B lines gives a reading of 6 kW. When the same terminal of the voltage coil are switched over to B- and C- lines, the current coil connections remaining the same, the reading of the wattmeter remains unchanged. Calculate the line current and the pf of the load.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If the line-to-line primary voltage and line current is 1.0 at 0 degrees, what is the secondary line- to-line voltage for the following three-phase transformers? Assume a turns ratio of N = 10. Express answer in polar form. a. Delta-to-Delta: b. Delta-to-Wye: c. Wye-to-Delta: d. Wye-to-Wye:
please write your Introduction about this topic , and answer please in print font do not write in hand writing ? beceuse I want to copy it ?
using zero power factor potier methode
(i) What are the causes and disadvantages of low power factor? (ii) A single-phase 400 V, 50 Hz motor takes a supply current of 50 A at power factor of 0.8 lag. The motor power factor has been improved to unity by connecting a condenser in parallel. Calculate the capacity of the condenser required. (iii) In a three-phase overhead line, the conductors have an overall diameter of 3.0 cm each and are arranged in delta formation. Assuming a critical disruptive voltage of 250 kV between the lines, an air density factor of 0.90 and mo = 0.95, find the minimum spacing between conductors that is allowable. Assume fair weather conditions.
Two power system areas operating at a nominal frequency of 60 Hz are connected with a tie line, and have the following characteristics: Area 1: R1 = 0.01 pu and D1 = 0.8 pu on a base of 1200 MVA Area 2: R2 = 0.02 pu and D2 = 1 pu on a base of 600 MVA The power flow direction on the tie line is from Area 1 to Area 2. Using a common base of 1000 MVA, what is the change in prime mover power (in MW) in Area 2 (APmech2) for a load increase of 125 MW in Area 1?
How does a three-phase power system differ from a single-phase power system, and what are their respective applications?
Overhead lines.
I need the answer as soon as possible
Answer question 4
Khalid Abdulrahman Abdullah Alqasmi KA 05 Symm... 9 Search 8 Share O Comments Transitions Animations Slide Show Review View Help 1. A 3- phase, 30 MVA, 33 KV alternator has internal reactance of 4% and negligible resistance. Find the external reactance per phase to be connected in series with the alternator so that steady current on short circuit does not exceed 10 times the full load. Also find Find the full load current. d notes
Please answer all subpart either dislike is ready.. please all subpart
The impedance present in a circuit is Z=4+3j ohm. Express the impedance in polar form.