a) With the aid ofa diagram, explain how you would improve the power factor ofan inductive load using synchronous motor marks] 8 b) b synchronous motor when connected parallel with the load improves the power factor of a load of 200KW from 80 lagging to 0.9 lagging. Simultaneously the motor carries a load of 80 KW. Calculate: The leading KVAR supplied supplied by the motor F The KVA rating of the motor The power factor at which the motor operates

a) With the aid ofa diagram, explain how you would improve the power factor ofan inductive load using synchronous motor marks] 8 b) b synchronous motor when connected parallel with the load improves the power factor of a load of 200KW from 80 lagging to 0.9 lagging. Simultaneously the motor carries a load of 80 KW. Calculate: The leading KVAR supplied supplied by the motor F The KVA rating of the motor The power factor at which the motor operates

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

5-A Load of particular kVA is drawing a current which lags behind the voltage at an angle of 75.43 degrees. The operating power factor is __________ . a. 0.5958 b. 0.2515 c. 0.6122 d. 0.6511
Q2/A/ The 2MW load operating with 0.8 lagging power factor. To improve the power factor to 0.95 a synchronous motor is connected in parallel with load. Find the (motor rated KVA and total system KVA
Refer to Figure 8-31 to answer the following questions. Assume that a line voltage of 12,470volts is connected to the primary of the transformer and the line voltage of the secondary is 480volts. What is the turns ratio of the transformer? Assume the load has an impedance of 6Vper phase. What is the secondary line current? How much current is flowing in the secondary winding? How much current is flowing in the primary winding? What is the line current of the primary?
Please answer all subpart either dislike is ready.. please all subpart
conductor radius is 0.75cm
ings of a 40 kVA, 6 m respectively. The le- ate (i) the primary vol ced (ii) the full-load re
Plant A - 150kVA, 0.68pf laggingPlant B - 70kVA, 0.65pf lagging It is desired to correct the power factor of the two plants by connecting a synchronous motor. When the synchronous motor is connected, the overall power factor is corrected to 0.95 lagging. Determine the overall power factor in kVA.
A 51 kVA load operates at 0.72 lagging power factor when connected to a 230 V, 60Hz AC source. The power factor is to be improved to 0.96 lagging. The power factor is to be corrected by a synchronous motor with 0.51 leading power factor, what is the kVA rating of the synchronous motor? The answer is 24.4643. Show solution pls
Khalid Abdulrahman Abdullah Alqasmi KA 05 Symm... 9 Search 8 Share O Comments Transitions Animations Slide Show Review View Help 1. A 3- phase, 30 MVA, 33 KV alternator has internal reactance of 4% and negligible resistance. Find the external reactance per phase to be connected in series with the alternator so that steady current on short circuit does not exceed 10 times the full load. Also find Find the full load current. d notes
Three load units A, B and C are connected in parallel and take currents that are respectively 12, 10 and 15 amperes. Assuming IA to be the reference phasor, IB leads IA by 30°, and IC lags IA by 65°, calculate the total current and the angle it makes with the reference.
using zero power factor potier methode
1. A load of 50 ohms resistance and 0.4 H inductance are connected in series to 100 volts, 60 hz a-c source. What must be the value of the capacitance to be connected in parallel to the circuit to raise the power factor to 0.96 lagging. Draw the circuit diagram.