A 1000 KVA, 400V three-phase electrical plant operates at a power factor of 0.6 lagging. It is desired to improve the power factor to 0.99 by installing capacitors. How much A is the current drawn after compensation? 3 fazlı 1000 KVA, 400V bir elektrik tesisinin güç katsayısı kompanzasyon yapılarak 0.6 dan 0.99'a çıkarılmak istenmektedir. Kompanzasyondan sonra çekilen akım 34- kaç A dir? O A) 925 O B) 875 O 9 1025 O D) 975 O E) 800

A 1000 KVA, 400V three-phase electrical plant operates at a power factor of 0.6 lagging. It is desired to improve the power factor to 0.99 by installing capacitors. How much A is the current drawn after compensation? 3 fazlı 1000 KVA, 400V bir elektrik tesisinin güç katsayısı kompanzasyon yapılarak 0.6 dan 0.99'a çıkarılmak istenmektedir. Kompanzasyondan sonra çekilen akım 34- kaç A dir? O A) 925 O B) 875 O 9 1025 O D) 975 O E) 800

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

b) Calculate the total power loss in the transmission lines
(2) EX! dregion as follow: from midnight to 5 am Lookw form 5 am to 6pm Nodo lodd from 6pm to c 7 P.m 800kw from 7 P.m to gp.m goo kw from 9 Pm to midnight Yookw sat plot. The daily Load curve and The Load dration curve A generation station of 1 MW supplied أعلى قيمة هي واحد فيها واط ۱۰۰۰۰ محکم مردن - عده الهم @find The Load factors. The reserve capacty Plant capacity factor Plant Use factor and utilization factor
Three loads are connected in parallel to a 240-V, 60 Hz supply. Load 1 is composed of three 600-W heaters, Load 2 is a 3 HP, inductive motor with an efficiency of 90% and a p.f. of 0.88, while Load 3 has an impedance of 12-j16 ohms. Determine the following: a) The apparent power of each load b) The Total Power, Total Reactive Power, Total Apparent Power, Power Factor c) The source current
Range of a generating voltmeter is 30 to 300 kV dc and its indicating meterreads a minimum current of 3μA and maximum current of 35 μA, find the capacitance of thegenerating voltmeter.
7- Which of the statements about the power factor being 1 is incorrect? a) Voltage and current are in phase b) Active power and reactive power are equal c) Phase angle is 0°. 606 d) All energy supplied from the source is consumed by the load
QUESTION 2 Calculate the magnitude of the reflected impedance for an ideal transformer that is connected to a 10V RMS supply and a 80 load, if the secondary draws 100mA RMS of current. O 1.25k2 O 80 O 8570 O 22.5kn
problem 2 1. what is the voltage provided by the building 2. What is the amount of current provided to the bullding? 3. If the building consumes 3200W of power, what is it's power factor? 4. What is the phase angle of the secondary power source in the bullding?
A 3-Φ, 5 KW induction motor has a p.f of 0.75 lagging. A bank of capacitors is connected in delta across the supply terminals and p.f raised to 0.9 lagging. Determine the KVAR rating of the capacitor connected in each phase. Also comment on the type of supplied KVAR, Whether it is unity, leading or lagging.
Show all steps and working please. A 250 μF capacitor is inserted in parallel with the supply producing a new improved power factor of 0.9345.
2.3. An inductive load consisting of R and X in series feeding from a 2400-V rms supply absorbs 288 kW at a lagging power factor of 0.8. Determine R and X.
Simulate the power electronics shown below in order to find the harmonics component of the load voltage. Note: your answer should be the same as the figure shown below. VT: VT; lo R 0.9 Fundameatal compacet 04 03 7th 9th 120 110" Triering angle (a) Harmenie componret of the load valiage (pa.)
A 3125 kVA turbogenerator operates with 2,500 kW and 0.8 inductive power factor. Another 330 kW load with inductive 0.85 power factor is added. What value of capacitors in kvar is necessary to connect to the system for the turbogenerator not to operate overloaded?