PROBLEM 9.3. A signal æ( t) is sampled with sampling rate fs, and the resulting sampled sequence x[n] is converted back to continuous time using an ideal DAC having the same f, parameter: 2(t). |r[n] ADC v(t) DAC f. sin (440rt) sin (420nt) sin (400rt) Suppose that æ(t) = and y(t) = A nt nt (a) Find A. (b) Find B. (c) Find f.

PROBLEM 9.3. A signal æ( t) is sampled with sampling rate fs, and the resulting sampled sequence x[n] is converted back to continuous time using an ideal DAC having the same f, parameter: 2(t). |r[n] ADC v(t) DAC f. sin (440rt) sin (420nt) sin (400rt) Suppose that æ(t) = and y(t) = A nt nt (a) Find A. (b) Find B. (c) Find f.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please help me, I want to solve this question without quoting or plagiarism, I hope that the solution is in Ms word and not in handwriting.
Ex. 410. G(s) =k (s+26)/ (s* (s+61)) is the forward transfer function (FTF) of a unity feedback closed-loop system. The CLCE can be written in the form: 1 + k(As^2 + Bs + C)/ (s^2 + D*s + E) = 0. Determine: A,B,C,D, and E. ans:5
d) A regulator as shown in Figure 4 has an input voltage, Vs 12 V. The duty cycle, k = 0.35 and the switching frequency is 30 kHz. It also has an inductance, L= 200 µH, filter capacitance, C = 440 µF. The average load current, la = 1.25 A. Determine the; i. average output voltage, Va. ii. peak-to-peak output ripple voltage, AVc. iii. peak-to-peak output ripple current of inductor, AI. iv. peak current of the transistor, Ip. v. critical values of L and C. vi. critical values of L and C if Vs is increased to 14 V. Estimate the change in percentage for the critical values of L and C. V, Load V V G Figure 4
Ex. 410. G(s)=k(s+31)/ (s* (s+92)) is the forward transfer function (FTF) of a unity feedback closed-loop system. The CLCE can be written in the form: 1 + k(As^2 + Bs + C)/ (s^2 + D*s + E) Determine: A,B,C,D, and E. 0. ans:5
Hello pls help me sir its easy kinda for y
Question 6 Full explainthe this question very fast solution sent me step by step Don't ignore any part all part work u Not:- Text typing work only not allow paper work
for the circuit if R = 5ohm, E = 20V and the cut-off (trigger) angle is 90 degrees; Draw the waveform of the source current Is, the output voltage VDC, and the output current Id Calculate the average value of output voltage VDC and output current Id.
a) For an opamp, the input bias current Ib =60µA and the input offset current lio= 20µA. Find the input base currents Ig1 and I82 b) Design an opamp circuit with the following output: Vo = - Vin/3 +5 c) For the given circuit, Vsat=D±13V Given : V1=1V and V2=2V , R2=2 kn , R1=1 k2 R3=R43DR5%3D1K ) Identify (name) the circuit (stage 1 and 2) i) Find the output voltage Vo. iii) Find Vo if the resistor Rs opens (removed). R3 R4 R2 ww Rs ww 10-ww stage1 stage 2
Consider the oscillation whose open-loop response is as follows: S+W3 (S+w)(S+w2) Suppose W, > W, > W3 A) Draw the geometric location of the roots of the closed loop system. B) Calculate the oscillation frequency. C) Using the above system, realize the oscillator orbit.
K A certain analog plant function is shown in figure 2 and its transfer function G,(s) = (s+a)(s+b)· This plant is sampled using a zero-order hold (ZOH) before the signal is fed to a digital controller. Using 0.45 second as sampling time and K=14; a=3; b=5, Do the following. Zero-order Plant Plant Hold ZOH Gp(s) G(z) Figure 2 i. Obtain the z-transform G(z) ii. Discuss the importance of a ZOH in digital control systems
1 (1) A plant in a unity feedback system is given by K G(s) s(s + 10)(s + 20) Find the value of K to get ? of the dominant closed-loop pole as 0.6 K = 887.4 K= 103.1 K= 152.2 None of these
|| For the circuit shown in the figure below, assuming that VA = ∞, the input impedance is expressed by: Vcc O O Q₂ Rc Vino O Select one: Q₁ a. Vout 1/9m1 b. 1/9m1 + BRc 1/9m1 + Rc None of these O c. O d. V₂