A vibration analyst wishes to record a frequency spectrum covering the range 0-10000 Hz with a resolution of 0.5 Hz. Calculate the necessary ADC sampling rate and also the necessary number of samples per spectrum.

Q: Define the following 1)Signal loss 2) Voltage gain 3) Frequency

A: According to the given question, it is required to define the below given parameters.  1) Signal…

Q: How would the hysterisis of an instrument affect its uncertainty? Suggest how to reduce the effect…

A: Hysteresis in an instrument is when it doesn't give you the same measurement when you're going up…

Q: In an LC oscillator, if the value of L is increased by four times, the frequency of oscillations…

A: In an LC oscillator if the value of L is increased by foure times the frequency oscillations is _

Q: What characteristics are used by mode 2 in the 8255?

A: We will refer the concept of microprocessor 8255

Q: In Steady-State Operation​ o​ f Buck DC-DC Converter Explain how the switching frequency component…

A: Steady-state operation of Buck DC-DC converter: A buck converter (step-down converter) could also…

Q: A chopper has input voltage of 290 and the load resistance as 50, the average load current as 50A.…

A: Chopper: The circuit which transfer the dc power from one circuit to another circuit at the required…

Q: 3. Design a PUT relaxation oscillator shown below by specifying the values of the other components…

A:

Q: For the relaxation oscillator, what would be the effect on the oscillation frequency of doubling CE…

A:

Q: A boost regulator has L=0.15 mH and C=0.11 mF with a duty cycle of 0.66 at a switching frequency of…

A: The peak to peak ripple in the output voltage is…

Q: The larger the value of the filter capacitor, the Select the correct response smaller the de voltage…

A: The solution is given below

Q: Report 4-1 IC 555 chip and using it as oscillator circuit to generate a binary output signal and a…

A: Astable IC 555 - The 555 Timer IC may be attached in both Monostable or Bistable mode to make a…

Q: Briefly explain the general signal conditioning functions used in ADC or DAC. And explain, how the…

A: ADC( Analog to digital converter) will convert an analog signal to a digital signal and the DAC(…

Q: (a). Write any two advantages of a digital signal over an analog signal.

A: We need to write two advantage of digital signal .

Q: Ex. 295. Refer to Figure 295 Determine: 2%Settle Time, Peak Time, Rise Time, Percent Overshoot,…

A: Settling time : The time it takes for the output to reach and stay within a specific error band…

Q: c) Calculate the required capacitor value for a frequency of 550k H z and find its time period. The…

A: Given:

Q: Define signal generator and list the requirements of laboratory type signal generator and raw block…

A:

Q: What type of A/D converter would work best for video signals with a frequency content up to 5 MHz?…

A: A/D converters (ADC) provide different speeds, different accuracy and use various interfaces. The…

Q: (2) Consider a frequency modulated signal. The modulating signal frequency is increased from 10 kHz…

A: In this question we have to find the correct optionsrgarding modulated signal bandwidth

Q: Estimate the maximum surge current in a half wave rectifier with a transformer having an rms…

A:

Q: khat Con ue cn aboul Paformana optimieadion Prom Amdahl's low?

A: Amdahl law : Amdahl law is related with the computer programming when ever there are programs which…

Q: harmonic oscillator

A: Harmonic oscillator circuit- Here, we will connect capacitor and inductor in parallel. Along with…

Q: need the answer as soon as possible

A:

Q: 1. Attenuator of -10DB has gain () 2. An output signal has a fundamental amplitude of 2.5V, second…

A: According to guidelines we are allowed to do only first three subparts. Please post again for…

Q: A chopper has input voltage of 290 and the load resistance as 50, the average load current as 50A.…

A:

Q: Explain the control strategies of Pulse width modulation technique and draw the waveform for duty…

A: Control strategies of Pulse width modulation technique

Q: 64) A circuit that provides a varying output signal, typically of square-wave or triangular-wave…

A: VCO is a type of oscillator that can produce varying outputs based on the DC voltage.

Q: A chopper has input voltage of 270 and the load resistance as 7N, the average load current as 53A.…

A:

Q: Discussion and elaboration on the importance of active filter in electronic system and relate it to…

A: We need to write the importance of active filter in electronic systems and also need to write how it…

Q: Discussion add elaboration on the importance of active filter in electronic system

A: Introduction: Active filters are utilized in communication systems for suppressing noise, to isolate…

Q: (3) A sinusoidal signal of frequency 200 Hz is sampled at a rate of 1200 samples per second. Draw…

A:

Q: Find stability of the system -alti h Ct) = e

A: If integration yields a finite values then the system is said to be stable

Q: 3- What are the factor which affect the frequence stability of an oscillator?

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Explain in detail, what is the difference between sampling and quantization

A: To create digital image continuous data is converted to digital form. This conversion needs two…

Q: A chopper has input voltage of 290 and the load resistance as 52, the average load current as 50A.…

A: The circuit transfers the dc power from one circuit to another the circuit at the required output…

Q: 3. Discuss the main reason for the probable error occurred during experiment

A: Bartleby has policy to solve only first question.  Reupload Rest questions.

Q: Offset voltage compensating network is connected in between pin of LM741 op-amp number ....... &...…

A: LM741 is an 8-pin operational amplifier. A LM741 op-amp is shown below,

Q: 5. The smallest amplitude pulse that can be generated by the stimulator is 100 mV. Describe how you…

A:

Q: Design  a +40 volt dc  power supply for your sound system.  Your sound system requires  a 400 watt…

A: Solution- Given specifications are, The input is a three-wire single-phase supply. DC voltage =40V…

BJT (Bipolar Junction Transistor)

A BJT is a semiconductor device with 3 terminals that consist of a p-n junction diode that can amplify the signal or current. It is a current-controlled device. The three BJT terminals are base, collector, and emitter. The BJT works with the charge carrier, the two type of carriers in the BJT are holes and electrons, the charge carriers flow by the process of recombination. The signal to be amplifier is generally given as the input at the base terminal and an amplified form of it is available at the collector terminal.