(s+a)(s+b) plant is sampled using a zero-order hold (ZZOH) before the signal is fed to a digital controller. Using 0.45 second as sampling time and K=14; a=3; b=5, Do the following. Zero-order Hold Plant Plant ZOH Gp(s) G(z) Figure 2 i. Obtain the z-transform G(z) ii. Discuss the importance of a ZOH in digital control systems

(s+a)(s+b) plant is sampled using a zero-order hold (ZZOH) before the signal is fed to a digital controller. Using 0.45 second as sampling time and K=14; a=3; b=5, Do the following. Zero-order Hold Plant Plant ZOH Gp(s) G(z) Figure 2 i. Obtain the z-transform G(z) ii. Discuss the importance of a ZOH in digital control systems

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For each of the plants represented by signal-flow graphs in Figure P12.2, determine the controllability. If the controllability can be determined by inspection, state that it can 5 511 15 -3 XA I (a) -2 (c) X لیل این امکار وکی 14 115 2-15 -3 Xy (b)
shows a block diagram of a process con- trol system. Determine the range of the gain K for stability. Figure K Figure Process control system. Verify using Nyquist on Matlab
Discuss the need of filter. Explain the working LC filter. Draw input and output waveform and derive the expression for ripple factor.
I need the answer as soon as possible
How to tell the difference between a open loop transfer function and closed loop transfer function?
1) Fast help needed to answer this Engineeing question. Check image. Postive feedback for right answer :)
9. PLOT. Plot the sine wave at frequency fm and the sampling signal at frequency fs1. Write a MATLAB program to take input both fm and fs1 and plot the curves mentioned above.,.
5 a) Consider the sample sequence (5000, 5000, 5000, 5000, -5000, -5000, -5000, -5000}. These are samples of a square wave with a period of eight samples or 1ms at 16 KHz sampling frequency. What are the sinusoidal frequencies in the output waveform?
A typical digital signal processing (DSP) system is given in figure below. ADC has 100MHZ sampling clock and every samples will be captured by FPGA for backend processing. An interpolator increases the sampling rate by a factor of 4 to generate the sample stream of y(n). Then, a decimation block will reduce the sampling rate by a factor of 15 to generate sample stream of z(n). 100MHZ FPGA z(n) Decimator x(t) х(п) y(n) ADC Interpolator LPF1 LPF2 i. When LPF1 (Low Pass Filter 1) and LPF2 are implemented using a 30-taps FIR structure, and the system must operate in streaming way (every samples must be processed without any halt), what will be required FPGA clock frequency and what type of FIR filter structures should be used? Input samples are 12-bits and coefficients are 10-bits for both filters. Determine the number and the size of multiplication and addition operations in FPGA to implement LPF1 and LPF2. Comment on the bit growth and what kind of digital operations should be…
?? Please ?? ?? Solve it in Digital Solution ?? The Subject is Power Electronics
A common application of control systems is in regulating the temperature of a chemical process (Figure P6.11). The flow of a chemical reactant to a process is controlled by an actuator and valve. The reactant causes the temperature in the vat to change. This temperature is sensed and com- pared to a desired set-point temperature in a closed loop, where the flow of reactant is adjusted to yield the desired temperature. In Chapter 9, we will learn how a PID controller is used to improve the performance of such process control systems. Figure P6.11 shows the control system prior to the addition of the PID controller. The PID controller is replaced by the shaded box with a gain of unity. For this system, prior to the design of the PID controller, find the range of amplifier gain, K, to keep the system stable. Desired temperature set point + Future PID controller Amplifier 1 H K Actuator and valve S + 0.5 0.1 s +0.1 Temperature sensor Chemical heat process 0.7 s² + 1.7s +0.3 Actual…
W/ explanations 9.) Find time Constant TC, Se Hling time Ts of - 4 (st (-4)) b.) Draw tine response Tr.