a) For an opamp, the input bias current Ib =60µA and the input offset current lio= 20µA.Find the input base currents Ig1 and I82b) Design an opamp circuit with the following output: Vo = - Vin/3 +5c) For the given circuit, Vsat=D±13VGiven : V1=1V and V2=2V , R2=2 kn , R1=1 k2 R3=R43DR5%3D1K) Identify (name) the circuit (stage 1 and 2)i) Find the output voltage Vo.iii) Find Vo if the resistor Rs opens (removed).R3R4R2wwRsww10-wwstage1stage 2

Answered: Image /qna-images/answer/ce7d9358-01da-4cec-9fe1-f611a84e4858.jpg

a) For an opamp, the input bias current Ib =60µA and the input offset current lio= 20µA. Find the input base currents I81 and Ia2 b) Design an opamp circuit with the following output: Vo = - Vin/3 +5 c) For the given circuit, Vsat=±13V Given : V1=1V and V2=2V , R2=2 kn, R;=1 k2 R3=R4%3DR5%3D1K2 D Identify (name) the circuit (stage 1 and 2) ) Find the output voltage Vo. i) Find Vo if the resistor Rs opens (removed). R4 R3 -wwww R2 Rs ww stage1 stage 2

a) For an opamp, the input bias current Ib =60µA and the input offset current lio= 20µA. Find the input base currents I81 and Ia2 b) Design an opamp circuit with the following output: Vo = - Vin/3 +5 c) For the given circuit, Vsat=±13V Given : V1=1V and V2=2V , R2=2 kn, R;=1 k2 R3=R4%3DR5%3D1K2 D Identify (name) the circuit (stage 1 and 2) ) Find the output voltage Vo. i) Find Vo if the resistor Rs opens (removed). R4 R3 -wwww R2 Rs ww stage1 stage 2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I. An op amp has a GBP of 10°. A 0.3 µV sinusoidal signal at 5 KHz is required to be amplified to 5 V. Calculate the gains and draw the schematic circuit to achieve this. II. K type thermocouple having a range of 0– 350 °C and a sensitivity of 40 uV/°C. The signal is connected to an instrumentation amplifier before interfacing it with 5V analog to digital converter. Design a suitable instrumentation amplifier circuit. Vsupply thermocouple Vout Instruni op Amp ADC Dout
1- Mention any two advantages of Integrated Circuit . 2- For the circuit given below : Vin is a sine wave Vinpp=6 V and Vref=-2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
Given the four statements, which of the following statements are true about an op-amp integrator? i. For an op-amp integrator wilh R = 10OKOhms, C = 10UF and a sine wave inpul waveform, the output waveform is a cosine waveform. %3D ii. For an op-amp integrator with R = 100KOhms, C = 10uF and a triangular input waveform, the output waveform is a square wave. iii. For an op-amp integrator with R- 100KOhms, C =10uF and a sine wave input waveform, the output waveform is a sawtooth waveform. v. For an op-amp integrator with R10OKOhms. C lCuF and a square wave input waveform, the output waveform is a triangular waveferm.
a) For an opamp, the input bias current Ib =60uA and the input offset current lio= 10uA Find the input base currents and In b) Design an opamp circuit with the following output: Vo = - Vin/4 + 2 For the circuit given below Given :Vin-0.2V, Vsat= 12V D Identify (name) the circuit (stage 1 and 2) O Find the output voltage Vo and the current through the load 4ka 0 Find Vo if the resistor 2kn opens 10 k Stage Stage 2 Vo Vin
In the voltage regulator circuit shown in the figure, the op-amp is ideal. The BJT has VBE=0.7 V and Beta = 100, and the Zener voltage is 4.7 V. For a regulated output of 9 V, the value of R (in Ohms) is Express answers in two decimal points. Show solution on your answer sheet. V = 12 V Vo = 12 V 1 k2 1 k2 AV2 = 47 V %3D ww
(d) An instrumentation amplifier is used when the application signal is very low. For the circuit shown in Figure Q2(d), calculate the applied input vin of the circuit to get the output of 5V at vo. Let Rr=360k 2 and R₁ = 12k 52. Rf www R1 Vec www Vo -Vec Figure Q2(d) (e) Illustrates instrumentation system for temperature measurement with the help of block diagram. Vin uA741
3R The op-amp will only slightly amplify signals: a.when the supply voltages are less than +/- 25V b.that are common on both the inputs c.that are different on both the inputs d.when the supply voltages are more than +/- 25V
Design a voltage to current converter amplifier. Assume that you have 5v input voltage to the non-inverting input with a frequency of 60hz and another input voltage to the inverting input with a frequency of 60hz, place it before the input resistance. What should be the value of your voltage input in inverting input and input resistance to get a reading of 38.22mA at exactly 22.20ms and what is the shape waveform of the current? What is the value of Vin?Vin = ____ volts
0.2 Design inverting circuits. an op-amp circuit to produce the output Vo= 8Vi, using both inverting and non 19
A. Design an Op-Amp based electronic circuit that can produce a uniform square waveform with peak values of 10V in positive and -10V in negative if the input signal is Vin = sin2nt?
3ZD Calculate the output voltage of an op-amp if a 100mV signal is applied to the non-inverting input of the op-amp circuit which has an Rf = 0 Ohms and Ri = 0 Ohms. a.Infinity Volts b.0 Volts c.1 Volts d.-2 Volts