Problem (4)For the control system shown in Fig. 4, design a compensator such that the staticvelocity error coefficient K. is 20 sec¹ without appreciably changing the originallocation (S = -2±J 2√3) of a pair of the complex conjugate closed-loop poles.1GAS)16Fig. 4, Control system for problem 4

static velocity error constant Kv = 20 sec-1

Answered: Problem (4) For the control system…

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter4: Numerical Analysis Of Heat Conduction

Section: Chapter Questions

Problem 4.6P

See similar textbooks

Similar questions

2- Using Matlab, what are the step response curves of the closed-loop system, as shown in fig.1. the feedback represents the second-order dynamic system. (fill in the following table) For=0.4 Wn 1 3 6 9 10 R(S) 0.1 0.3 0.6 0.9 1 For w 5 rad/sec 3 Settling time Peak response 2 Wn s(s+23wn) Settling time Peak response C(s) Discuss the follow Which parameters or w occur on the rise time of the response? Which parameter increases the speed of response? Which parameters can be decreases the response amplitude? Which parameter decreases the steady error state? fig.2
Q5) For unity feedback control system with forward transfer function (G(s) ): G(s) = ; By using root locus graph calculate the value K(s+5) (s+2)(s²+12s+50) of gain (K) which must be added to get the dominant root at damping ratio (-0.886) and natural frequency (w = 8 rad/sec )? www CTRICAL ENGIN
Please don't provide handwritten solution ....
1) Consider the system below: Vehicle Controller Steering dynamics Desired Actual bearing angle bearing angle 50 1 K s2 + 10s + 50 s(s + 5) Figure 1: Simplified Block Diagram of a Self-Guiding Vehicle's Bearing Angle Control. • Find a K value that the system has minimum rise time and minimum overshoot. Let us call this proportional gain as Kopt Show each step while finding Kopt- Show the necessary graphical solutions. Simulate the system response with 3 different K values. (Kopt and two other K values close to Kopt) Show the system response (actual bearing angle) in a single graph for different K values. • Comment on the results.
For the given close-loop system transfer function, determine its stability using Routh-Hurwitz Test for Stability.1. What is the stability of the system? (Stable, Unstable, Marginally Stable)
Can you also please do the simulate the step response in MATLAB for the design and report archieved PO and settling time? Thank you.
K = 5.3
answer completely and neatly
I need the answer quickly
please explain step by step
and 1) 2) LIUS S Consider the following feedback system, where K is a constant gain G(s) === 1 s3 +382 +s+1 Let K be a real number. Utilize the Routh-Hurwitz criterion to derive stability conditions for the closed-loop system. Suppose that the reference input r(t) = 1. What are the steady-state tracking errors (ess) for K = 1 and K = 3, respectively? R K G(s) Y Figure 2: Control system in Problem 2.
Q5 Hydraulic power actuators were used to drive the dinosaurs of the movie Jurassic Park. The motions of the large monsters required high-power actuators requiring 1200 watts. One specific limb motion has dynamics represented by: y = [0 1] Design the state feedback gain matrix using the Ackermann's formula method. Where the new closed loop poles to be placed at s1,2 =-17j3.

SEE MORE QUESTIONS

Recommended textbooks for you

Principles of Heat Transfer (Activate Learning wi…

Mechanical Engineering

ISBN:

9781305387102

Author:

Kreith, Frank; Manglik, Raj M.

Publisher:

Cengage Learning