PROBLEM 2: The steel beam loaded below has the built-up cross section as shown. Determine the maximum permissible value of the load w so as not to exceed allowable bending stresses of 110 MPa. -125 mm- w (including beam weight) 20 mm 20 mm 100 mm · NA - 2 m→- 6 m -2 m→ 20 mm

PROBLEM 2: The steel beam loaded below has the built-up cross section as shown. Determine the maximum permissible value of the load w so as not to exceed allowable bending stresses of 110 MPa. -125 mm- w (including beam weight) 20 mm 20 mm 100 mm · NA - 2 m→- 6 m -2 m→ 20 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Answer all.a.A mild steel flat of width b= 150 mm, thickness t = 20 mm and length L= 6000 mm carries an axial pull P = 300 kN. If modulus of elasticity of mild steel is 200 GPa and Poisson’s ratio is 0.25, calculate the change in length, width and thickness of the flat. B.A stepped bar made of brass is subjected to axial loads as shown in the below figure. Determine the total change in length of the bar. Take E =100 GPa.figure is attached C.A thin cylinder of external diameter 820 mm, length 3 m and wall thickness of 10 mm is subjected to an internal pressure of 2.5 N/mm2 . Determine the change in diameter and length. Take Young’s modulus = 2×105 N/mm2 and Poisson’s ratio = 0.25.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
Question 5 A steel column with a rectangular hollow section is subject to a vertical downward load P1 and a horizontal load P2, as shown in Figure 5 below. If the width of the hollow section is 70mm and the thickness is 5mm, determine the maximum compressive stress at the base of the column. P1=500KN, P2=100kN. P1 - P2 e =110mm Top plate- P2 P1 1m L120mm 120mm (b) Top view showing location of loads (a) Column elevation Figure 5: The cantilever column is fixed at the base.
The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 94 GPa] with a cross-sectional area of A₁ = 280 mm2. Bar (2) is an aluminum alloy [E = 71 GPa] with a cross-sectional area of A2 = 590 mm². All bars are unstressed before the load P is applied; however, there is a 3-mm clearance in the pin connection at A. Assume L₁ = 1840 mm, a = 880 mm, b = 540 mm, c = 430 mm, and L₂ = 1340 mm. If a load of P = 87 kN is applied at B, determine (a) the normal stresses in both bars (1) and (2). (b) the downward deflection of point A on the rigid bar. h (1) L₁ b a BI Answers: C (2) D L2
The prismatic rod shown is made of a steel that is assumed to be elastoplastic with E = 200 GPa and oy = 280 MPa. Knowing that couples M and M' of moment 525 N·m are applied and main- tained about axes parallel to the y axis, determine (a) the thick- ness of the elastic core, (b) the radius of curvature of the bar. y M 18 mm 24 mm X 'M'
The aluminum W 310 x 202 (wide flange) column is subjected to an eccentric axial load P as shown. The maximum compressive stress in the column is given by the so-called secant formula: where --- [¹ + ( √5)] ec o 1+ sec max E ō = P/A = average stress A = 25800 mm² = cross-sectional area of the column e = 85 mm = eccentricity of the load c = 170 mm = half depth of the column r = 142 mm = radius of gyration of the cross section L = 7100 mm = length of the column E = 71 x 10⁹ Pa = modulus of elasticity Determine the maximum load P that the column can carry if the maximum stress is not to exceed 120 × 10^6 Pa. Terminate the computation when Σa < 0.0005%.
A load P is applied to a steel component which is supported an aluminum plate into which a 12 mm diameter hole has been drilled. Knowing that the maximum allowable shearing stress is 86.5 MPa in the steel and 160 MPa in the aluminum plate, determine the largest load which may be applied to the steel component. Provide your answer in kN with precision to two decimal points. 10 mm Answer: 12 mm 40 mm P 8 mm
The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 95 GPa] with a cross-sectional area of A1 = 260 mm2. Bar (2) is an aluminum alloy [E = 69 GPa] with a cross-sectional area of A2 = 690 mm2. All bars are unstressed before the load P is applied; however, there is a 3-mm clearance in the pin connection at A. Assume L1 = 2000 mm, a = 1080 mm, b = 610 mm, c = 460 mm, and L2 = 1380 mm. If a load of P = 100 kN is applied at B, determine(a) the normal stresses in both bars (1) and (2).(b) the downward deflection of point A on the rigid bar.
Q4 (b) Figure Q4(a) shows a steel beam with length of 4 m that is supported by a steel column at point B. The steel column of AB has a rectangular cross section (40 mm× 70 mm). The ends are assumed to be pin connected. The yield stress of steel is o y 250 MPa. The Modulus Elasticity of the steel is 200 GPa. Use factor of safety of 1.5. (i) Check whether the Euler's equation is appropriate or not. (ii) Determine the maximum distributed load (W) that can be applied to the beam so that the column of AB does not buckle.
A simply supported beam, circular in cross section, of span L supports a point load W at mid span. The length of elastic-plastic zone at the plastic hinge will be A 0.33 L B 0.41 L C 0.50 L D 0.58 L
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 78 GPa. The steel rod has a diameter of 16 mm and an elastic modulus of E = 200 GPa. Assumea = 4.1 m, b= 1.2 m, and c= 1.2 m. What is the magnitude of load P that is necessary to displace point A 12 mm to the left? a (1) (3) A B (2) Answer: P = i kN
1/2 Problem 1: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown in. If the stress must not exceed 14OMPA in either rod, determine the smallest allowable value of the diameter of rod AB and ВС. 300mm B 40 kN 250mm - d2 30 kN