A load P is applied to a steel component which is supported an aluminum plate into which a 12 mm diameter hole has been drilled. Knowing that the maximum allowable shearing stress is 86.5 MPa in the steel and 160 MPa in the aluminum plate, determine the largest load which may be applied to the steel component. Provide your answer in kN with precision to two decimal points. 10 mm Answer: 12 mm 40 mm P 8 mm

A load P is applied to a steel component which is supported an aluminum plate into which a 12 mm diameter hole has been drilled. Knowing that the maximum allowable shearing stress is 86.5 MPa in the steel and 160 MPa in the aluminum plate, determine the largest load which may be applied to the steel component. Provide your answer in kN with precision to two decimal points. 10 mm Answer: 12 mm 40 mm P 8 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 με is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P?
The screw clamp shown in the figure applies a P = 500 N pressing force to the wooden blocks between the jaws. In this case; a) Calculate the greatest tensile and compressive stresses occurring in the section a-a shown in the figure. b) Show the distribution of normal stresses across the section height. (draw) c) Since the clamp material has tensile strength (apull) safety = 50MPA and compression safe stress (opress) safety = 80MPA, what is the great compressive load (P) that can be applied without damaging the a-a section? %3D %3D (Please solve in detail and according to engineering rules.) Material mechanics Sectional view a-a - 20mm T. 183mm 40mm
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
A small aluminum alloy [E = 80 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 430 µɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P ЗР Strain gage d D E H Answer: P = i
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress (in Mpa) in the bronze given that P= 188 kN? Express your answer in four decimal places.
The state of plane stress shown occurs at a critical point of a steel machine component. As a result of several tensile tests, it has been found that the tensile yield strength is o, = 250 MPa for the grade of steel used. Determine the factor of safety with respect to yield using (a) the maximum shearing stress criterion, and (b) the maximum distortion energy criterion. ↑y 40 40 MPa 80 MPa 25 MPa ➜X
One of the following values is a possible for possion ratio for steel ? a. Zero b. one c. 0.3 d 0.9
Question 4a pls
I need the answer quickly
A small aluminum alloy [E = 73 GPa] teeshape is used as a simply supported beam as shown. For this beam, a = 150 mm. The cross- sectional dimensions of the teeshape are b = 25 mm, d= 38 mm, and t=7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 490cis measured from a strain gage located at c= 9 rmm below the topmost edge of the tee stem at section 1-1. What is the applied load P? 3P Strain gage d a a H Answer: P = i