Figure Q4(a) shows a steel beam with length of 4 m that is supported by a steel column at point B. The steel column of AB has a rectangular cross section (40 mm× 70 mm). The ends are assumed to be pin connected. The yield stress of steel is o y 250 MPa. The Modulus Elasticity of the steel is 200 GPa. Use factor of safety of 1.5. (i) Check whether the Euler's equation is appropriate or not. (ii) Determine the maximum distributed load (W) that can be applied to the beam so that the column of AB does not buckle.

Figure Q4(a) shows a steel beam with length of 4 m that is supported by a steel column at point B. The steel column of AB has a rectangular cross section (40 mm× 70 mm). The ends are assumed to be pin connected. The yield stress of steel is o y 250 MPa. The Modulus Elasticity of the steel is 200 GPa. Use factor of safety of 1.5. (i) Check whether the Euler's equation is appropriate or not. (ii) Determine the maximum distributed load (W) that can be applied to the beam so that the column of AB does not buckle.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The solid rod has a diameter of 20mm. Find the following: Angle of twist at C with respect to A (in radians) Angle of twist at B with respect to A (in radians) Maximum shear stress at A (in MPa) (Shear stress at support, at a point 7mm from center. (in MPa) A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C
The state of plane stress shown occurs at a critical point of a steel machine component. As a result of several tensile tests, it has been found that the tensile yield strength is o, = 250 MPa for the grade of steel used. Determine the factor of safety with respect to yield using (a) the maximum shearing stress criterion, and (b) the maximum distortion energy criterion. ↑y 40 40 MPa 80 MPa 25 MPa ➜X
Determine the following: Displacement of B (in mm) with respect to A. Displacement of C (in mm) with respect to A. Principal stresses at point O, if it is 200mm from C. (unit should be kPa). A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
i need the answer quickly
When designing a structural member, which of the following statements is FALSE? Select one: A. The allowable stress is used in calculating the maximum load to be applied. B. The ultimate stress depends on the Factor of Safety used. C. The ultimate stress is determined based on the material used. D. The allowable stress depends on how conservative the design is.
The rigid bar of negligible weight is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises by 20∘C after a load W = 110 kN is applied. Use the following properties in the table.
I will rate immediately
One of the following values is a possible for possion ratio for steel ? a. Zero b. one c. 0.3 d 0.9
Determine (d) variable stress and (e) design factor
pls help me. thank u refer to the picture attached below.
Step by step solution *