PROBLEM 2: The assembly in figure 2 shows four gears ABCD, a hollow shaft BC with inner and outer diameters of 92 mm and 125 mm respectively, and solid shafts AB and CD of diameter d. For the loading shown, determine the following: a) the maximum and minimum shearing stress in the shaft BC b) the required diameter of shafts AB and CD if the allowable shearing stress in these shafts is 65 MPa. Use T = Tp/J 09m 0.7 m 05m 120 m TA = 7 k-m , and Tg = 14 km Tc = 28AN-m Tp=7 AN-m Figure 2

PROBLEM 2: The assembly in figure 2 shows four gears ABCD, a hollow shaft BC with inner and outer diameters of 92 mm and 125 mm respectively, and solid shafts AB and CD of diameter d. For the loading shown, determine the following: a) the maximum and minimum shearing stress in the shaft BC b) the required diameter of shafts AB and CD if the allowable shearing stress in these shafts is 65 MPa. Use T = Tp/J 09m 0.7 m 05m 120 m TA = 7 k-m , and Tg = 14 km Tc = 28AN-m Tp=7 AN-m Figure 2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the 2-in.-diameter shaft is made from cast iron having tensile and compressive ultimate stress of 1sult2t = 50 ksi and 1sult2c = 75 ksi, respectively, determine if the shaft fails according to Mohr’s failure criterion.
A force of 100N is applied to the free end of a restrained beam, shown in the figure. The wall thickness is 2 mm from the upper and lower walls (1-6, 2-3, 4-5) and 4 mm on the side walls (1-2, 5-6). Calculate the normal stress distribution and the maximum stress in the middle section.
The shear diagram is shown in the figure, determine the moment and load diagrams. Show your solution
3. Please show your complete solution. Please typewritten for upvote.
HW A shaft composed of Segments Ac, CD and DB fastened to rigid supports and loaded as shown, for st G=83 GN/m², for Aluminum G =28GN/m² and for br G= 35 GN/m² Determine the maximum shearing Stress developed in each Segment? Steel d=25mm 2m Ans: TB-472 N.M, TAI = 9.1 TD=700N.. Tc=300N.m Aluminum d= Semm 1.5m & ₁ B Bronze d=25mm Im
Situation 1| Consider the figure 1 below. 3- 25mmØ bolts are used to fasten a plate to a steel beam. 1) Determine the average shearing stress caused in each bolt by the 30kN loads 2) Determine the value of additional load P that must be applied so that each bolt will not exceed the maximum shearing stress of 60MPA. 30 kN 150. 300 200 30 kN P.
complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94 What will be the maximum weight of cylinder that can be put as shown in the figure below if the maximum stress at cable is FN mPa? Note: Round off your answer in two decimal places.
M A solid steel circular shaft is required to transmit a torque of 1600 N without exceeding an allowable shear stress of 55 MPa nor an allowable rate of twist of 1° per metre. The required diameter (d) of the solid shaft will m. Take shear modulus of be material to be 80 GPa. ——————
Q₂ for for the ystem showing complute The qixah deformation at A, B 4. A=160mm 2 E=90061 5KN/m + ↓ 3m tram obm 15 KN 444=1.5 A=350 6-75 & for B
The following tubular A36 steel shaft has an inner diameter of 25mm and an outer diameter of 35mm under the following loading condition. Determine the angle of twist of the end V. Consider: GA-36 = 75 GPa 1) What would happen if a solid shaft was used? 2) As a designer, do you recommend a solid or tubular shaft for the loading above? Why?
8. Please include FBD & make the solutions understandable
2. For the system shown below, compute the maximum torque it can accommodate if a is 2000mm and b is 150omm. Assume that the bronze segment, has a diameter of o.o75m, t < 60 MPa, and G = 35x10^3 MPa. On the other hand, assume the steel segment has a diameter of 0.05m, t < 80 MPa, and G = 83x10^3 MPa. b A