Situation 1| Consider the figure 1 below. 3- 25mmø bolts are used to fasten a plate to a steel beam. 1) Determine the average shearing stress caused in each bolt by the 30kN loads 2) Determine the value of additional load P that must be applied so that each bolt will not exceed the maximum shearing stress of 60MPA.

Situation 1| Consider the figure 1 below. 3- 25mmø bolts are used to fasten a plate to a steel beam. 1) Determine the average shearing stress caused in each bolt by the 30kN loads 2) Determine the value of additional load P that must be applied so that each bolt will not exceed the maximum shearing stress of 60MPA.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A flanged bolt coupling consists of six 20- mm diameter steel bolts spaced evenly around a bolt…

Q: Three steel plates are joined by three 20-mm diameter rivets. If the ultimate shear stress in the…

Q: A steel angle is bolted to a gusset plate with three 20 mm diameter bolts, as shown in the figure.…

Q: With the dimensions already given, determine the allowable value of the tensile load P, considering…

Q: 26 Problem: splice plate shown in the accompanying figure 2.26 consists of a 250 mm x 10 mm el plate…

A: Diameter of holes, Minimum Tensile strength,

Q: 2. A steel plate is 360 mm wide and 20 mm thick with four bolts hole into the place as shown in the…

A: Answer Given data b= 360 mmt=20 mmNo. of bolts- 4

Q: X A cylindrical part of diameter "d" is loaded in tension by a load "P" causing a stress: a-P/A. The…

A: Given, Uncertainty in load = ±15% Uncertainty in diameter = ±7.5% Uncertainty in stress = ±15%

Q: A bolt with a diameter of 24 mm is used to join two steel plates together. The plates are subjected…

A: Given: diameter of bolt, d = 24mm Load on steel plate: P = 120KN Allowable shear stress in bolt =…

Q: hected on both legs with 12 mm diameter bolts. Given that s = 50 mm

A: consider figure for solution

Q: 143. Which of the following is not a built-up shape? Double angles c. Plate girders d. Unequal leg…

A: 143. Built-up section are the sections made by joining two or more hot rolled sections. Double…

Q: 6.8 Problem: A bracket shown in figure 6.8 carries an eccentric load of 80 kN at an eccentricity o…

Q: Q.2: A rectang steel. The bar hole drilled th axial loading Using ASTM m estimate the cycles. Taken

A: Given- Cycle- 60,000 Sut= 64 Width of bar= 50mm Thickness= 8mm Hole= 10mm Notch sensitivity, q= 0.8…

Q: A loading causes the wires to elongate into the dashed shape. Determine the normal strain in wires…

Q: bolted lap joint

Q: Two plates are connected using three 20-mm-diameter bolts as shown in the figure. If the axial load…

A: P = 50KN Determine the shear stress in each bolt.

Q: The pin support at A has a double-shear steel bolt as shown. Determine the required diameter of the…

Q: An A36 tension plate is 9 mm thick is given below. Bolts are 20 mm. Given that s = 50 mm and g =…

A: Given data in question Thickness of plate Diameter of bolt Bolt lines Guage distance To find out…

Q: A steel [E = 200 GPa] rod with a circular cross section is 11 m long. Determine the minimum diameter…

A: Allowable stress=170 MPaForce=230 kN = 230000 NStress=ForceArea170=230000π4×d2d=41.5 mm

Q: A plate with width of 500 millimeters and thickness of 25 millimeters is to be connected to a double…

Q: The given angle bar L125x75x12 with Ag = 2,269 sq.mm. is connected to a gusset plate using 20 mm…

Q: Give me right solution

A: Given data L8×6×12 Steel used is A572 gr. 42 Diameter of bolt=1 in.

Q: The angle shown in the figure is L 7 X4 X 7/16. Steel used is AS72 Gr. 55 steel. Diameter of bolts…

A: diameter of bolt = 1.125inch distance between two bolts=3inchs Ag=4,62in2 by steel table fy =70ksi…

Q: Calculate the value of P so that the allowable tensile stress on net area will not be exceeded. USE…

Q: The group of 6-bolts connection subjected to eccentric load P=30 kips as shown in figure. The…

A: Given a bolted assembly, it is required to find the maximums hear force.

Q: Situation 8: For the connection shown in the figure. Pu = 80 KN, x1 = 200, x2 = 100, y1= 50, y2 = y3…

Q: (1) Given A992 steel Ag = 10 in KLx KLy- 80, ry what is $Pa=? = 60 the design column strength

Q: Two plates are connected by a bolt as shown in the figure. What is the shear stress on the bolt? D…

Q: determine: (a) the elastic section modulus and the yield moment. (b) the plastic section modulus…

Q: A bracket shown in the figure 6.9 carries an eccentric load of 30 kN at an eccentricity of 200 mm.…

Q: A plate is fastened to a fixed member by four 16mm rivets arranged as shown. Compute the maximum…

A: To determine the shear stress in the rivets. Given, Diameter of the rivets (d) = 16 mm From the…

Q: An A36 tension member shown in the figure is connected with three 19 mm diameter bolts. Dia. Of bolt…

Q: The bracket shown in the figure is supported by four 22 mm diameter bolts in single shear. The…

A: The bracket shown in the figure is supported by four 22 mm diameter bolts in single shear. The…

Q: determine the minimum bolt diameter

A: Given data:P=230 KN or 230×103NAverage shear stress,τavg=125 MPa or 125 N/mm2

Q: A steel rod with length equal to 7.5 ft, has a diameter of 0.78 inches in quarter of its length and…

Q: The bolted connection shown must support an applied load of P = 5300 kN. The average shear stress in…

A: The values and diagram given in the question are as follows: Applied load(P)=5300 kN or 5300*103 N…

Q: A steel connecting rod with length of 6 meters and is to be subjected to a tensile load of 70 KN.…

A: ΔL = 4 mm = 0.004 m F = 70 kN = 70,000 N L = 6 m E = 200 GPa = 200,000 MPa = 200,000,000 N/m2To…

Q: s used as a tension member connected on both legs with 20 mm diameter bolts. Given that s = 50 mm,…

A: Given:- 20 mm diameter bolts s = 50 mm t=8mm Ag=1852mm2 To find:- Design strength

Q: 50mm 50mm 50mm P

A: Tension of plates = 75 MPaeffective hole diameter = 23 mm the joint efficiency = 80%

Q: À steel beam is welded according to the figure below with two welds. The beam is loaded with a force…

A: (a) For 20mm thick member a (minimum size of weld) = 5mm

Q: What is the approximate value of the tensile strength governed by yielding of the cross- section of…

Q: 2. For the figure shown below, determine the following; (60 points) a. Maximum tensile stress b.…

A: We have to determine the value of maximum tensile stress and maximum compressive stress and…

Q: What will be the tensile strength due to rupture of critical section of an angle section ISA 150 x…

Concept explainers

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).

Question

Situation 1| Consider the figure 1 below. 3- 25mmØ bolts are used to fasten a plate
to a steel beam.
1) Determine the average shearing stress caused in each bolt by the 30kN loads
2) Determine the value of additional load P that must be applied so that each
bolt will not exceed the maximum shearing stress of 60MPA.
30 kN
150.
300
200
30 kN
P.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Step by step

Solved in 9 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please include the detailed explanation and diagram
An A36 tension member shown in the figure is connected with three 19 mm diamter bolts. Diameter of hole = 22mm. Properties of 150 mm x 100 mm x 12.5 mm angle A = 3065 mm2 y = 50.55 mm Fy = 248 MPa Fu = 400 MPa Determine the desire strength due to fracture in the net section. Use U = 0.85 kN
Pls answer both question, you'll get a like ty <33 Dont round off initial values, only round off in final answer ty
The rectangular plate (L,xL,) given below is installed between two rigid walls and is deformed as shown by dashed lines. Determine the shear strain y and Yxy at point A. Use the table given below and your student ID to find the values of L, L, a, and b. L2 A b. L. b L, (mm) (mm) (mm) 150 200.0 3.0 3.0
Question 9 Not yet answered Pants out of 100 The bolt in the figure below has a diameter of 0.75" inch. If the load P is 14,700 lbs, determine the average shearing stress in the bolt. 4E P fy= Select one: Oa 8.3k/in Ob. 83 k/in OC 601 k/in Od. 16.6k/in Oe. 33.2 k/in
An A36 tension plate is 10 mm thick is given below. Bolts are 20 mm. Given that s = 65 mm and g = 70 mm, calculate the net area at tensile fracture line d-e-b-f-g in mm2. Write your answer rounded to the nearest whole number.
Please show a detailed solution and explanation including its FBD. Thank you!
An A36 angle bar is used as a tension member connected on both legs with 12 mm diameter bolts. Given that s = 50 mm, calculate the design strength (kN) by LRFD with the limiting state of tensile fracture at the smallest possible net area. Write your answer to the nearest whole number. Ag = 1,852 mm2 t = 8 mm
1
The Aluminum plates below are connected by two 3/4" diameter bolts. What is the shear stress in the bolts given the load applied?
Please show complete solution and explanation thank you
A steel beam is welded at the left and loaded as shown below. It has a rectangular cross section (height=h, thickness=t) with L=1m, a=0.4 m, h=3 cm, t=1 cm, F=500 N, w=200 N/m. a. Find the factor of safety if the material is 1020 Steel that has been hot rolled (hint: ductile) using an appropriate failure theory b. Find the factor of safety if the beam is the materials is gray cast iron number 50 (hint: brittle) using an appropriate failure theory. а F W