HW A shaft composed of Segments Ac, CD and DB 1 fastened to rigid supports and loaded as shown, for st G=83 GN/m², for Aluminum G=28GN/m² and for br G= 35 GN/m² Determine the maximum shearing Stress developed in each Segment? Steel d=25mm 2m X Ans: TB-472 N.M, TAI = 9.1 TD=700N.. Tc=300N.m Aluminum d= Semm 1.5m for B Bronze d=25mm Im

HW A shaft composed of Segments Ac, CD and DB 1 fastened to rigid supports and loaded as shown, for st G=83 GN/m², for Aluminum G=28GN/m² and for br G= 35 GN/m² Determine the maximum shearing Stress developed in each Segment? Steel d=25mm 2m X Ans: TB-472 N.M, TAI = 9.1 TD=700N.. Tc=300N.m Aluminum d= Semm 1.5m for B Bronze d=25mm Im

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

10/10 find the tensile stress in upper plate in section 3-3 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 10 MPа О 12.5 MPa 15 MPa 8.5 MPa O no one O ---.. O- O O 300mm 8 mm
Consider the truss shown in (Egure 1). Suppose that F-60 kN and F₂-25 kN Figure 40 KN Part C Fau 50 AN Submit -2m- D 15m 1of1 > 15m 15m μA Value -F₂ Part A Request Answer Determine the force in member ED of the truss, and state if the member is in tension or compression Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. HA FED Value Submit Part B Request A Determine the force in member EH of the truss, and state if the member is in tension or compression Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Submit Fon- Value Determine the force in member GH of the truss, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of…
Find the stresses in A, B and C? 14-d Vem 14 6m 0.006 MN 0 cm B -HA- 4 IX 6em H
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
The assembly consists of three disks A, B and C that are used to support the load of 140 kN. Determine the smallest diameter d, of the top disk, the diameter d₂ within the support space, and the diameter d of the hole in the bottom disk. The allowable bearing stress for the material is (allow)b = 350 MPa and allowable shear stress is allow=125 MPa. B A 140 KN - dz d₂ 20 mm 10 mm
A traffic light signal pole is subjected to the weight of each traffic signal 45 lbs and the weight of the road lamp 55 lbs . The weight of lateral arms is included in the signal and lamp weights. The people is fixed and the base and is made of round structural steel section HSS 14.000 x 0.25. The details of the pole section may be obtained form the Manual of American society of steel Construction (AISC Steel Manual). Analyze the principle normal stresses and the maximum shear stresses on elements A and B located at the base in the pole as shown in the sketch below.
Point B & C. Please complete solution and no rounding off.
From Steel Design Topic Include complete solution
QL/ Twe rad have the Same cross- Sectional area; Mad from steel anel Bron ze as shown in fig1. Find the stress in each rood when Est = 200GPa j Eb=83Gpa. br st 3m 30 30 Fig1
Q2. Design a rivet that is utilized in a double riveted butt joint which connects two 12 mm thick plates. The efficiency of riveting joint is 80% and the pitch is 80 mm. If the allowable stresses for the plate material are (tensile stress o 100 MPa, shear stress - 75 MPa, bearing stress oc= 180 MPa) and for the rivet material are (tensile stress o-120 MPa, shear stress T-90 MPa, bearing stress 6 = 200 MPa), use F.S. = 1.
If P=13000 N, d=22mm and t=33mm, determine the bearing stress between the rivets and plate, in MPa?
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P= 20 KN is applied. Sleel E-200 GPa A-400mm L1 m 2.0 m 0.6 m 1.5m P-20 KN Aluminum E70 GPa A-900mm L-1.5 m 1. Axial load at steel rod in kN? 2. Axial stress at steel rod in MPa? 3. Axial deformation of aluminum rod in mm? 4. Axial deformation of steel rod in mm? 5. Axial Load at aluminum rod in kN?