Problem 2: A shaft is to be fitted with a flanged coupling having 6 bolts on a circle of diameter 150 mm and 4 bolts on a circle of diameter 100 mm. The shaft Outer bolt Shaft circle may be subjected to either a direct tensile load of 400 kN or a twisting moment of 18 kN-m. If the maximum direct tensile and shearing stresses permissible in the bolt material are 125 MPa and 55 MPa respectively. Find the minimum diameter of the bolt required. Assume that each bolt takes an equal share of the load or torque. Shaft IBolt Inner bolt Flange circle

Problem 2: A shaft is to be fitted with a flanged coupling having 6 bolts on a circle of diameter 150 mm and 4 bolts on a circle of diameter 100 mm. The shaft Outer bolt Shaft circle may be subjected to either a direct tensile load of 400 kN or a twisting moment of 18 kN-m. If the maximum direct tensile and shearing stresses permissible in the bolt material are 125 MPa and 55 MPa respectively. Find the minimum diameter of the bolt required. Assume that each bolt takes an equal share of the load or torque. Shaft IBolt Inner bolt Flange circle

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.2.1P

See similar textbooks

Similar questions

For the rivet connection shown in figure 2-4, the allowable shearing stress in the 25mm rivets is 140 MPa. Assume the plates are adequate to transmit the load to the rivets. P= 60 KN. a) Determine the shearing stress in the most stressed rivet. b) Determine the maximum allowable value of P. c) If P=80 KN, determine the minimum diameter of rivets. USE NSCP 2015. Thanks.
The following image shows a front and side view of the column connection. The bolts have a diameter of ¾”. The W12X65 profile has a thickness of 0.605”. Determine:a. The shear stress in the bolts.b. The axial stress in the bolts.c. The support stress in the W12X65 profile.
The five-bolt connection shown must support an applied load of P = 400 N. The thickness of the axial member: = 1 mm. and the width = 16 mm If the ultimate shear stress in the bolts must be limited to 250 MPa with F.O.S = 2.5 . And the ultimate normal stress in the axial member = 180 MPa, with F.O.S = 2.9 , And the ultimate bearing stress in the axial member = 95 MPa, F.O.S = 1.3 Determine the minimum bolt diameter that may be used in the connection? In correct way
The five-bolt connection shown must support an applied load of P = 300 N. The thickness of the axial member: = 1.5 mm. and the width = 18 mm If the ultimate shear stress in the bolts must be limited to 265 MPa with F.O.S = 3.7 . And the ultimate normal stress in the axial member = 250 MPa, with F.O.S = 2.8 , And the ultimate bearing stress in the axial member = 110 MPa, F.O.S = 2.5 Determine the minimum bolt diameter that may be used in the connection
I need the answer as soon as possible
KINDLY ANSWER IN CLEAR EXPLANATION.
A 20-mm-thick plate is bolted to the flange of a T-beam to form a 200 mm 20 mm built-up beam. If the beam is subjected to a vertical shear force of V = 200 kN, determine (a) the maximum shear stress in the beam, 10 mm 300 mm (b) the required spacing s of the bolts. The diameter of each bolt is 19 mm, and the allowable average shear stress in the bolts is 140 MPa. 10 mm
10/10 find the tensile stress in upper plate in section 3-3 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 10 MPа О 12.5 MPa 15 MPa 8.5 MPa O no one O ---.. O- O O 300mm 8 mm
For the given riveted connection shown, having the allowable stresses: Fy = 248 MPa Fy = 150 MPa (shear stress) Tensile stress=0.60 Fy Bearing stress = 1.35 Fy Rivet hole has a diameter 2mm greater than the rivet diameter. The main plate has a width of 300mm and a thickness of 20mm. Determine the diameter of rivets such the shear capacity of the rivets is equal to its bearing capacity. Also, compute the maximum value of P so as not to exceed the allowable tensile stress of plates. P- O JAK O O 300 mm -P/2 -P/2
For the given riveted connection shown, having the allowable stresses: Fy = 248 MPa Fy = 150 MPa (shear stress) Tensile stress = 0.60 Fy Bearing stress = 1.35 Fy Rivet hole has a diameter 2mm greater than the rivet diameter. The main plate has a width of 300mm and a thickness of 20mm. Determine the diameter of rivets such the shear capacity of the rivets is equal to its bearing capacity. Also, compute the maximum value of P so as not to exceed the allowable tensile stress of plates. 300 mm t/2 -P/2 P- -P/2
The plate welded to the end of the I-beam is fastened to the support with four 10-mm-diameter bolts (two on each side). Assuming that the load is equally divide among the bolts, determine the normal and shear stresses in a bolt. Express your answer in MPa.
The steel tie bar shown is to be designed to carry a tension force of magnitude P = 120KN when bolted between double brackets at A and B. The bar will be fabricated from 20-mm-thick plate stock. For the grade of steel to be used, the maximum allowable stresses are: o = 180 MPa, t = 120 MPa, op = 380 MPa. Design the tie bar by determining the required values of: a. the diameter d of the bolt, b. the dimension b at each end of the bar, c. the dimension h of the bar.