A flanged bolt coupling consists of ten 16-mm-diameter bolts spaced evenly around a bolt circle 650 mm in diameter (D). Determine the torque capacity of the coupling (in kN-m) if the allowable shearing stress in the bolts is 40 MPа.

A flanged bolt coupling consists of ten 16-mm-diameter bolts spaced evenly around a bolt circle 650 mm in diameter (D). Determine the torque capacity of the coupling (in kN-m) if the allowable shearing stress in the bolts is 40 MPа.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.8.1P: Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.

See similar textbooks

Related questions

Q: The five-bolt connection must support an applied load of P = 149 kips. If the average shear stress…

Q: The plate welded to the end of the I-beam is fastened to the support with four 10-mm-diameter bolts…

A: The data given is a I beam inclined at 40o subjected to a 30 kN force, and is supported by two bolts…

Q: The steel tie bar shown is to be designed to carry a tension force of magnitude P = 120KN when…

Q: For the given riveted connection shown, having the allowable stresses: Fy = 248 MPa Fy = 150 MPa…

Q: Two bolts are used to lap points two steel plates. Tensile force on the plate is 45KN. Determine the…

Q: A double-row butt joint is used as a connection. It is made up of two 210mm by 12mm cover plates and…

Q: Q3. A solid shaft was made of alloy steel, it was welded to a flat plate by a specific size of…

Q: R, RD

A: Given: A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm.…

Q: The bolted connection shown must support an applied load of P= 2200 kN. The average shear stress in…

A: P=2200kN To find diameter of bolt

Q: For the connection shown, the bolt diameter is d = 15 mm. The average shear stress in the bolts…

Q: A flanged bolt coupling consists of 6 - 12 mm - diameter bolts on a bolt circle of 320 mm i…

A: Given data in question Shearing stress Torque Diameter To find out Additional number of bolts…

Q: A flanged bolt coupling consists of 9-17-mm-diameter steel bolts on a bolt circle 400 mm in…

Q: The pin in the image shown below must transfer an axial tension force of 12.7 kN. Calculate the…

A: First we need to find the value of yield strength using steel through internet.

Q: 9. The gusset shown is riveted to the column flange by 7-20mm diameter rivet single shear. Determine…

A: The values and diagram given in the question are as follows: diameter of rivet(ϕ)=20 mm Number of…

Q: A flanged bolt coupling consists of 10-14-mm-diameter steel bolts on a bolt circle 500 mm in…

A: The given data is shown below: 10-14mm bolts on bolt circleDiameter of bolt circle=500 mm6-14mm…

Q: The steel shafts are connected together using a fillet weld as shown in the figure below. (Figure 1)…

A: T = 63 N. m

Q: A 100 x 100 x 10 mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN…

A: Retaining walls are moderately robust walls used laterally to hold soil so as to be retained on both…

Q: The gusset is riveted to a larger plate by 4 – 22mm rivets in single shear arranged and loaded as…

A: Given:- The diameter of the rivets = 22 mm The number of rivets = 4 The magnitude of the load = 60…

Q: PROBLEM 7. Determine the largest load P that can be applied the plate and bolts. The bolt has a…

Q: A flanged bolt coupling consists of 9-17-mm-diameter steel bolts on a bolt circle 600 mm in…

Q: A plate is fastened to a fixed member by four 16mmo rivets arranged as shown. Compute the maximum…

A: Shearing stress is defined as the force that tends to cause deformation of a body or material by…

Q: The five-bolt connection shown must support an applied load of P = 330 kN. If the average shear…

Q: For the given riveted connection shown, having the allowable stresses: Fy = 248 MPa Fy = 150 MPa…

A: The given figure is shown below:

Q: A flanged bolt coupling consists of 9-17-mm-diameter steel bolts on a bolt circle 400 mm in…

Q: For the rivet connection shown in figure 2-4, the allowable shearing stress in the 25mm rivets is…

Q: Two circular shafts are joined together between fixed supports to resist a torsional moment of 80…

Q: The bolted connection shown must support an applied load of P = 5300 kN. The average shear stress in…

A: The values and diagram given in the question are as follows: Applied load(P)=5300 kN or 5300*103 N…

Q: The five-bolt connection shown must support an applied load of P = 371 kN. If the average shear…

A: Given Load 371 kNStress 174 MPaNumber of bolts 5To find out Minimum diameter

Q: The bolt is made of a material having an allowable tensile stress of 140.44 MPa and an allowable…

A: Given:- The allowable tensile stress = 140.44 MPa The allowable shearing stress = 55.44 MPa The…

Q: Determine the design tensile strength of plate (200 x8 mm) connected to 10-mm thick gusset using 20…

A: Given, Yield stress of the plate fy=250 N/mm2 d=20 mm Diameter of the hole do=20+1=21 mm Ultimate…

Q: A 100 x 100 x 10 mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN…

A: Fillet welds are normally some of the most widely used joints in the welding field. It is the joints…

Q: A single unequal angle 100 x 75 x 6 is connected to a 10 mm thick gusset plate at the ends with six…

A: Given data, For a single unequal angle 100x75 is connected to a 10 mm thick gusset plate at the ends…

Q: A flanged-bolt coupling consisting of six % inch diameter steel bolts evenly spaced around a bolt…

Q: 4.002 Three bolts are used in the connection shown in the figure. The thickness of plate (1) is 15…

A: Given : thickness of plate 1 = 15 mm the ultimate shear strength of bolt 350 MPa The ultimate…

Question

A flanged bolt coupling consists of ten 16-mm-diameter bolts spaced evenly around a bolt circle 650 mm in diameter (D). Determine the torque capacity of the coupling (in kN-m) if the allowable shearing stress in the bolts is 40
MPa.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A flanged bolt coupling consists of 6 - 12 mm - diameter bolts on a bolt circle of 320 mm in diameter. Compute the number of additional 10 mm - diameter bolts on a bolt circle 200 mm in diameter to increase the torque capacity to 7.65 kNm. The shearing stress of the bolts should not exceed 60 MPa. Select one: O a. 6 bolts O b. 4 bolts O c. 3 bolts O d. 2 bolts NEXT PAGE
The bolted connection shown must support an applied load of P = 5300 kN. The average shear stress in the bolts must be limited to 250 MPa. Determine the minimum bolt diameter that may be used in the connection. Answer: Minimum bolt diameter = i mm
Two bolts are used to lap points two steel plates. Tensile force on the plate is 45kN. Determine the required diameter of the bolts if the failure shear stress of the bolts is 350 MPa. Use a factor of safety for shear equal to 2.0
9. The gusset shown is riveted to the column flange by 7-20mm diameter rivet single shear. Determine the stress in the most heavily loaded bolt. If the design shear stress is 400MPA, determine the ultimate load that the connections can carry. Using the design shear stress how much more torque can the connections carry? 140 kN 200 mm 175 mm 7- 20 mm bolts 150 mm 150 mm 150 mm
P4.002 Three bolts are used in the connection shown in the figure. The thickness of plate (1) is 15 mm. The ultimate shear strength of the bolts is 350 MPa, and the ultimate bearing strength of plate (1) is 375 MPa. Determine the minimum bolt diameter required to support an applied load of P = 155 kN if a minimum factor of safety of 2.8 is required with respect to both bolt shear and plate bearing failure. Answer: dbolt min = (1) mm
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesDetermine the maximum load P that can be applied to the lap joint connected bythree – 16 mm diameter rivets. Note: Draw its FBD
The five-bolt connection shown must support an applied load of P = 371 kN. If the average shear stress in the bolts must be limited to 174 MPa, determine the minimum bolt diameter that may be used in the connection. Answer: d = i mm.
The following image shows a front and side view of the column connection. The bolts have a diameter of ¾”. The W12X65 profile has a thickness of 0.605”. Determine:a. The shear stress in the bolts.b. The axial stress in the bolts.c. The support stress in the W12X65 profile.
Problem No 2 A flanged-bolt coupling consisting of six 4 inch diameter steel bolts evenly spaced around a bolt circle 12 inches in diameter and four inch diameter aluminum bolts on a concentric circle 8 inches in diameter. What stresses are developed on each bolt of the two bolt-circles when a torque T=75 Kip-in is applied. Use Gs=12 x 10° psi and GA = 4 x10° psi.
choose letter of correct answer
Please solve it correctly,Simple problem.
For the given riveted connection shown, having the allowable stresses: Fy = 248 MPa Fy = 150 MPa (shear stress) Tensile stress=0.60 Fy Bearing stress = 1.35 Fy Rivet hole has a diameter 2mm greater than the rivet diameter. The main plate has a width of 300mm and a thickness of 20mm. Determine the diameter of rivets such the shear capacity of the rivets is equal to its bearing capacity. Also, compute the maximum value of P so as not to exceed the allowable tensile stress of plates. P- O JAK O O 300 mm -P/2 -P/2