A SHAFT OF TO RIGID SUPPORTS SEGMENT AC, AND LO. FOR BRONZE 6= 35 and FIK STEEL, 6 = 83 6Pa Shearing stress develope of TA BRONEE Tc=300N-M ALUMINUM

Q: Please use slope and deflection method to calculate the moment at the fixed support A. 54kN/m A 15m…

A: From the given fixed beam and it is required to calculate moment at the fixed support A by using…

Q: The 10-minute triangular unit hydrograph for a watershed has a peak discharge of 100 ft’/s at 40…

A: 10-minute triangular unit hydrograph peak discharge(Q)=100 ft3/s (occur at 40 minutes) Total…

Q: Solve the given frame and write the values of reactions, shear force and bendi

A: Solution: Given data: UDL=32 kips

Q: A nozzle is so shaped that the average flow velocity changes linearly from 1.5 m/s at the beginning…

A: Given velocity- V1=1.5 m/s V2 =15 m/s  Distance dx=0.375 m

Q: Pipe in Series: Consider the two reservoirs show in below figure, connected by a single pipe that…

A: As the pipes are in series, Discharge will not be changes . Here we need to determine Disharge (Q).…

Q: A helical spring, with small slope of helix, is supposed to transmit a maximum pull of 2 kN and to…

A: Given data- A helical spring- Maximum pull = 2 kN, Extension of 10 mm for 400 N load, Mean diameter…

Q: Calculate the resultant of all force acting on the structure. 3. Rx = [Rx] KN use 2 decimal places…

A:

Q: Locate the centroid of the shape y. and moment of inertiaahout the x-axis•Itis a parabola and opers…

A:

Q: 5 as well

A: To calculate the clean bed head loss for the filter using the Carmen-Kozeny equation for both media,…

Q: Joseph Rivera Proportional Reasoning (Fractions and Decimals) Nov 11, 5:32:48 PM The table below…

A:

Q: A 0.9-m³ soil specimen weighs 17 kN and has a moisture content of 9%. The specific gravity of the…

A: Given Data  Total volume of soil specimen (V) = 0.9 m3  Total weight of soil specimen (W) = 17 KN…

Q: Consider a continuous flight auger pile in a sandy soil de- posit 10 m long with a diameter of 0.45…

A: Given:

Q: 1- Determine and locate the resultant R of the three forces and one couple acting on the beam about…

A: Given beam,

Q: A 20 cm diameter well penetrates an Artesian aquifer, 35 m thick. The discharge from this well for a…

A: Given that,

Q: A tube well of 30 cm diameter F uifer. The strainer length is 15 m. Calculate the yield fre 3 m. The…

A:

Q: 11. Determine the moment of inertia of the fully- cracked transformed section, I (in 10 mm). 12.…

A:

Q: 3- Bending strength of a construction material is 105 MPa. The porosity of this material is 5% and…

A: Relation between Bending strength and porosity is given in the question. We will use this relation…

Q: Q4/ An 6 lane divided highway is to be constructed on a new alignment. Traffic volume forecasts…

A: Transportation engineers use the annual average daily traffic (AADT) in the transportation analysis.…

Q: Q1) At a particular time, the storage in a river reach is 60 x 103 m 3. At that time, the inflow…

A:

Q: 2. A rectangular beam has a width of 280 mm and an effective depth of 500 mm. It has a reinforcement…

A: 2.

Q: Q3) Classify the rain gauges in your opinion; if you want to check the rainfall over an area, how…

A: A rain gauge is defined as the meteorological instrument which was used to measure the liquid…

Q: naximı a. 1ocation of left end of the beam b. maximum value of Ely c. Ely value at midspan um…

A:

Q: Water is to be pumped out of a deep well under a total head of 95 m. A number of identical pumps of…

A: Data given, Total head H = 95m Design speed N = 1000rpm Sp speed Ns= 900rpm Q = 150 l/s

Q: A wastewater sample was diluted 10% with tap water for conducting BOD Test. The DO content in…

A: Given that, Dilution percentage= 10% Initial D.O of waste water (D.oi)=   1.2mg/l  Final D.O. of…

Q: Interval 1630 to 1645 1645 to 1700 1700 to 1715 1715 to 1730 Total Northbound T 207 230 241 238 916…

A: g NB, TH  = 33.2 sg NB, LT  = 17.3 sCycle length, C = 125 sAs vehicle green for through movements is…

Q: solve the problem 4

A: Given data in question  Loads Span 7.5 m Simply supported beam  To find out  Moment at A and B

Q: What is the mean "flow of pollutant", QC, into the lake in grams/min? Show calculations. Since the…

A: Given data: flow rate Q = 4 m3/minmean μ' = 10gm/m2standard deviation σ' = 2gm/m3

Q: Two rainfall storms of magnitude 4 cm occurring on two consecutive 6- hr durations on a catchment of…

A: For any catchment under the storm or rainfall, water discharge occurs, this is a storm discharge we…

Q: In the highway construction in PLUS Berhad at Senawang R&R, a distance, x (m) of rough ground is…

A:

Q: Q2/ Figure below illustrates a compound curve, if the intersection angle between two tangents is…

A:

Q: A footing 2 m x 3 m in size transmits a bearing pressure of 140 kN/m2 on a soil having E= 5 × 104…

A:

Q: 1.1 According to the ACF and partial ACF plots make decision that which model can be fitted to the…

A: White noise model - Unsuitable because of irregular variance in the data MA 1  Very suited in non…

Q: 60 A square shallow foundation is to be constructed over a layer of sand. Given Df = 1 m; No is…

A: Given; Df = 1m ; qnet = 350 Kn/m2  sand is normally consolidated

Q: Q-Penetrate the rainwater from due to absorption or defect in the connection of building unites or…

A: Water penetrates through any materials if it has voids in it. Such voids make a way for water to…

Dependence on mechanical properties

The mechanical properties of materials are those structures that include the reaction to the load used. Metal switching features determine the scope of the usefulness of the content and establish the expected service life. Machine structures are also used to help distinguish and identify material objects. The most common mechanical properties considered are strength, ductility, stiffness, impact resistance, and resilience to fractures.