Solve using paper:PROBLEM 19: The horizontal top of a concrete column is subjected to the system of forces shown. Represent the resultant of all forces as a force R at point O PROBLEM 19: The horizontal top of a concrete column is subjected to thesystem of forces shown. Represent the resultant of all forces as a force R atpoint O4 kN0.8 m3 kNj-0.8 m2 kN0.8 m 2 kN1 kN0.4 m3 kN5 kN3 kN04 m

First, we need to identify the forces and their positions. The forces given are: 4 kN at 0.8 m, 3…

PROBLEM 19: The horizontal top of a concrete column is subjected to the system of forces shown. Represent the resultant of all forces as a force R at point O 4 kN 0.8 m 3 kNj-0.8 m 2 kN 0.8 m 2 kN 1 kN 0.4 m 3 kN 5 kN 3 kN 04 m

PROBLEM 19: The horizontal top of a concrete column is subjected to the system of forces shown. Represent the resultant of all forces as a force R at point O 4 kN 0.8 m 3 kNj-0.8 m 2 kN 0.8 m 2 kN 1 kN 0.4 m 3 kN 5 kN 3 kN 04 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Need answer now
Given the figure below determine the bar force at AB and BD
N1
Replace the loading acting on the beam (Figure 1) by a single resultant force. Suppose that F₁ = 500 N, F₂ = 340 N, and F3 = 750 N. igure F₁ 60° -2 m 4 m F₂ B -3 m F3 1500 N-m 1 of 1 Determine the magnitude of the resultant force. Express your answer to three significant figures and include the appropriate units. ► View Available Hint(s) F = Submit Part B 0 = Part C O x = Determine the angle between the resultant force and the x axis. Express your answer in degrees to three significant figures. ► View Available Hint(s) μА Value Submit VL ΑΣΦ Units μA Value ↓↑ vec Specify where the force acts, measured from B. Express your answer to three significant figures and include the appropriate units. ► View Available Hint(s) R ? Units ? ? counted counterclockwise from the negative x axis
Problem 4 The beam loaded as shown below, compute the bending stresses at every 1m from the fixed end support of the beam use Ina = 100x106 mm4 www 10 kN 4 kN/m bm 러 n.a. 130 mm 200mm
A ab Ask Copilot + 2 of 4 60 7/02/18 Question 1 CCB 221-STRENGTH OF MATERIALS (2015/16 SESSION) QUIZ 1-26 FEB 2016-(GROUP C) The stepped bar ABC of Figure Q1 is subjected to two axial forces as shown. The magnitude of the force P applied at C is not known. The bar cross-sectional areas are 12 cm² and 18 cm² for segments AB and BC respectively. The modulus of elasticity of the bar is 10 GPa. (a) (i) Calculate the magnitude of the force P if the displacement at end C is zero. (ii) Determine the normal stress in each segment of the bar indicating which is tensile or compressive. [6 marks] [3 marks] (iii) Determine the normal stain in each segment of the bar. (b) If for some reason it is required that the normal stresses in both segments be the same, calculate the magnitude of the force P and the normal strains in both segments of the bar. [3 marks] [6 marks] 55 KN B 9 A P 12 cm² 18 cm² 30 cm + 20 cm Activate Go to Sett Figure Q1 12°C Partly cloudy
Example Determine the x and y components of cach force acting on the gusset plate of a bridge truss. Show that the resultant force is zero. F - 6 kN F = 8 kN 888 F= 4 kN F- 6 kN 833 888
Solve the exercise
Problem 2: A uniform concrete slab of total weight 100 kN is to be attached as shown to two rods whose lower ends are on the same level. O Determine the tensile force of the aluminum rod so that the slab will remain ievel. ® Determine the ratio of the area of aluminum rod to the steel rod so that the Steel E=200 GPa L=6m Aluminum E=69 GPa L=4m slab will remain level. Determine the vertical displacement of the concrete slab if the aluminum rod has a cross sectional area of 320 mm?, with the slab remaining at horizontal level. 3 m 6 m m
A thin beam with a solid rectangular cross-section is loaded as shown in Figure Q7 below. W W L/3 L/3 L/3 Figure Q7 What is the ratio of the maximum to nominal shear stress for the beam described in Question 7? O a. 3:2 O b. 1:4 Ос. 3:1 O d.2:1 O e. 1:2 O f. None of the provided answers are correct. O 8. 1:1
A rectangular steel block 250 mmx100 mmx80mm is subjected to axial loads as follows. 480 kN (tensile in direction of its length) 900 kN (tensile on 250mm x 80 mm faces) 1000kN (comp. on 250mm x100mm faces) taking E=200 GN/m2 and 1/m=0.25 find a). Change in dimensions (height, width and length) b). Change in volume of the block c). Volumetric Strain c). Values of N and K (Module of Rigidity and Bulk Modulus) for material of the block. d). Determine the volume difference if the temperature of block increased by 20K. (Take alpha steel = 11.7 x 10-6 / 0C ) e). Discuss the behavioral characteristic for given application Comparing the impact from given mechanical loadings and thermal loadings to the block.
Problem 19.4 A beam is made up from 3 plates, as shown, to serve as a support rail for a crane hoist in a factory. The beam spans 30 feet. The hoist is supported by a carriage, as shown. IF|the system capacity is governed by the strength of the beam, determine the maximum load that can be lifted by the hoist. Take the allowable flexural stress in the beam to be 12 ksi. 30 feet 2.5 feet ½" x 4" plate 4" x 10" plate ½" x 8" plate Crane hoist carriage